Error code reference

GE Dishwasher Error Codes

204 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.
00No error detected.130Temperature sensor failure indicated during service mode main pump test on 3-digit…888CSM is tripped97Turbidity sensor failure indicated during service mode auxiliary pump test on 3-digit…AcFHigh supply voltageAdcInternal board failure (critical fault).ALL STATUS LIGHTS + BEEPINGControl errorALL_FLASH_BEEPControl error indicated by all status lights (SENSING, WASHING, RINSING, DRYING…AUTOTemperature faultAUTO & HEAVYDrain faultAUTO & HEAVY flashDrain fault-water not drained after 120 seconds; program stopped.AUTO & SPEEDTurbidity sensor faultAUTO & SPEED flashTurbidity sensor fault-process assumes high turbidity in case of uncertainty in the Auto…AUTO flashesTemperature faultBoostThermistor error-Control detecting short or open circuit at thermistor.C1Pump out portion of the cycle takes longer than 95 seconds, indicating a partially…C2Pump out time is more than 400 seconds; control stops the pump for 5 seconds then…C3Dishwasher will not go into pump out; the control did not receive an electrical signal…C4Control detects a flood condition within the dishwasher; control will beep at 1 second…C5Control detects two consecutive pump out times of less than 6 seconds, indicating no…C6Water temperature too low after the maximum 20-minute extension of the detergent wash…C7Control checks the temperature sensor at start of each wash cycle to determine if the…C8Detergent cup is blocked from opening fully; the latch arm continues to hold the sensor…CdCancel drainCFEContinuous Fill ErrorCleanTurbidity Sensor ErrorCLEAN FLASHINGControl error on Profile models indicated by flashing CLEAN LED and beeping sound.CLEAN flashing (alone)Unit has no waterClean LEDTurbidity sensor errordE RESETDetergent cup has been accidentally latched; display shows when RESET pad is touched…dLFDoor latch failure (critical fault).Door ThermistorOpen circuit door thermistor (temperature sensed below 32°F) or short circuit door…DRY (flashing)Value modelsDRYING FLASHINGControl error on Profile Performance models indicated by flashing DRYING LED and beeping…dSDrain system failureE0Thermal sensor cut (open circuit in tub thermistor).E1Water fill time too long-water supply valves are not open.E2Drain time too long-drain hose position may be too high.E3Heater failure-if heating for 90 minutes cannot reach the setting temperature in service…E4Overflow failure-some elements of the dishwasher leak causing the overflow detection…E5Not enough water is entering the dishwasher, or the drain pump is temporarily blocked…E6Water temperature in the dishwasher did not reach the proper wash temperature, usually…E7The temperature sensor in the dishwasher is not functioning properly; dishwasher will not…ERMembrane switch or its connection to the entry/display module is faulty.F0Failed turbidity sensorF1Failed turbidity sensorF112Key stuck on UI control.F128Low rinse aid detected in the unit.F144Replace inverterF145Inverter has detected incorrect AC Voltage.F146Replace circulation pump.F147Replace drain pump.F148Replace motor with faulty TCO (thermal cut out).F149Poor connection or harness to inverter.F150Inverter phase current fault.F151Continuous flow fault; water level reaches flood stage several times and has to drain.F152Continuous heaterF153Door latch failure.F154Door latch diagnostic failure.F155Tactile key stuck.F158Overvoltage condition detected by the control.F159Circulation pump fuse faultF16Communication error with UI board.F2Communication failedF201Flood switch fault detected.F202A connection issue has been detected at the water valve.F203A fault has been detected on the machine control board.F204A fault has been detected on the machine control board.F205A fault has been detected with the detergent cup.F206The pump motor fuse is open.F207A fault has been detected on the machine control board.F208A fault has been detected on the machine control board.F209A fault has been detected on the machine control board.F210A fault has been detected on the machine control board.F211Check heater TCO; a fault has been detected on the machine control board.F212A fault has been detected on the machine control board.F213Check heater TCO; a fault has been detected on the machine control board.F214AC connections fault detected.F215AC connections fault detected.F216Check heater TCO and AC connections; no failure detected with machine control board.F217A fault has been detected on the machine control board.F218A fault has been detected on the machine control board.F219A fault has been detected on the machine control board.F220A fault has been detected on the machine control board.F221A fault has been detected on the machine control board.F222A fault has been detected on the machine control board.F223A fault has been detected on the machine control board.F224No failure detected with machine control board; pump motor fuse blown, or heater TCO…F225Check heater TCO; a fault has been detected on the machine control board.F226Check heater TCO; a fault has been detected on the machine control board.F227Check heater TCO; a fault has been detected on the machine control board.F228Check heater TCO; a fault has been detected on the machine control board.F229Check heater TCO; a fault has been detected on the machine control board.F230A fault has been detected on the machine control board; check heater TCO and all AC…F231CSM trip detected.F3Configuration ErrorF32Pressure sensor reading falls out of range or is unplugged.F33Pressure sensor reading too low during calibration.F34Water present or detected in the drain pan (floor protect pan detected error).F35Diverter feedback error; feedback communication from diverter is not present or not…F36CSM (Current Sense Module) tripped / CSM lock out.F37Diverter feedback error.F4Failed turbidity sensorF48Turbidity sensor reading high (possible open on sensor).F49Turbidity sensor reading low (possible short on sensor).F5Inverter Found On Incorrect MC PersonalityF50Temperature sensor high; sensing or stuck at a high reading.F51Temperature sensor low; sensing or stuck at a low reading.F52Turbidity sensor did not successfully calibrate.F53Fuse failure with circulation pump on.F54Drain pump failure.F55Blown pump fuse on main control board.F56Failure to drain fault code.F58Dry heater thermistor errorF59Dry heater thermistor errorF6Communication lost with wireless module (on some models).F60Heater relay stuck on fault.F61CSM check failed.F62Dry fan not working properly.F63Flood condition faultF64Inverter-specific error detected.F65Inverter did not detect water; will not allow heater to turn on (failsafe).F66Dry heater TCO fault; heater or a TCO is open, temperature is out of range.F80Absent water flow (turbidity based); water flow not detected in unit.F86No fill failure; pressure sensor does not sense filling.F87Thermistor install fault; thermistor did not see the proper heat rise during the cycle.F96No water in tub (turbidity based); water not detected by turbidity sensor.F97Absent heat source; Calrod (heater) not detected by machine control.F98Non-draining sump (turbidity based); unit not draining or not being detected by turbidity…F99Minimum Wash Temperature of 120°F was not reached in 3 of the past 5 wash cycles.Fast Wash LED flashingNot Filling faultFFLine power failure occurred during cycle.FtdFailure to drain (critical fault).FuSBoard circulation pump fuse failure (critical fault).H20No water detected; internal water level does not change, cycle is cancelled (displayed on…H2ONo water detectedHeated DryWash Temperature Error-Minimum wash temperature of 120°F was not reached in 3 of the past…Heated Dry LEDWash Temperature Error-The minimum wash temperature of 120°F was not reached during 3 of…Heated Dry LED flashingOverfill faultHEAVYOverfillingHEAVY flashesOverfillingHrFInternal board failure (critical fault).LdLong drainLEAK DETECTEDThe dishwasher's leak detection system has detected a possible leak; the dishwasher will…LIGHTWater intake faultLIGHT flashesWater intake fault-fewer than 80 pulses within 60 seconds, or correct number of pulses…LockAlways illuminated when Error Code Display Mode is active; indicates Consumer Error Mode…Lock LEDAlways illuminated when Error Code Display Mode is active; indicates error mode is…Lock LED (Always Illuminated)Illuminates when Error Code Display Mode is active, indicating fault conditions are…Lock LED + continuous beepFactory Test Mode calibration failureLOCK LED illuminated (Factory Test)Turbidity sensor check has failed during factory test modeLOCK LED illuminated + continuous beeping (Factory Test Mode)Turbidity sensor check has failed during factory test mode; control module, wiring, and…Lower ZoneWater Level Sensor error-Failure in detection or operation of water level sensor.NORMThermistor faultNORM flashesThermistor fault-thermistor stopped or temperature exceeds 175°F; program continues.NORMAL FLASHINGControl error on Profile models indicated by flashing NORMAL LED and beeping sound.Normal Wash LED flashingNot Heating faultNot DrainingController has not sensed that the machine is empty after 5 minutes of draining.Not FillingPressure switch has not sensed water present after the selected fill time plus an…Not HeatingWater temperature has not risen by greater than 9°F in 15 minutes during a heating cycle.Over TemperatureWater temperature sensed exceeds 180°F but is less than 210°F.OverfillLeak detection switch closed or 2nd level pressure switch activated indicating an…PdPlugged drainPFPower failure has occurred; the last cycle selection was erased and an automatic…PF RESETElectrical power to the dishwasher has been interrupted but is now back on.POTS/PANS (flashing)Value models F-1 test diagnosticPrFPressure sensor failure; pressure sensor signal is undetectable or irrational (displayed…PrSPressure sensor error; pressure sensor signal is undetectable or irrational (displayed on…RINSEPressure sensor faultRINSE (flashing)Value modelsRinse & Hold LED flashingNot Draining faultRINSE flashesPressure sensor fault-output signal greater than 4.8 VDC; program continues.RINSINGFlood prevention errorRINSING + BEEPINGRinsing status light flashing plus a beeping sound indicates a cycle fault requiring…RINSING FLASHINGControl error on Profile Performance models indicated by flashing RINSING LED and beeping…RINSING_FLASHControl error indicated by the RINSING status light flashing along with a beeping sound.RINSING_FLASH_BEEPThe RINSING status light flashes accompanied by a beeping sound, indicating a water fill…SENSINGCleanSensor errorSENSING + WASHING + BEEPINGControl errorSensing LED not litTurbidity sensor circuit has failed open or is shorted; unit will operate for maximum…SENSING OFFCleanSensor errorSENSING_FLASHCleanSensor error-the sensing light does not illuminate during NORMAL or POTS & PANS…SPEEDLeaking valveSPEED flashesLeaking valveStartCommunications failureStart LEDCommunications Failure-User Interface control is unable to communicate with the machine…START/RESETCycle has been interrupted by pressing the START/RESET keypad; the light will quit…START/RESET flashingCycle has been interrupted by pressing the START/RESET keypad; the dishwasher will…START/RESET flashing + CLEAN flashingCycle has been interrupted by pressing the START/RESET keypad; light will quit flashing…STATUSControl errorSTATUS_FLASH_BEEPAll STATUS lights flash accompanied by a beeping sound, indicating a control error.Super Wash LED flashingOver Temperature faultTurbidity Sensor High SignalTurbidity sensor count is greater than 65,279 in 0.4 seconds.Turbidity Sensor Low SignalTurbidity sensor count is less than 50 in 3 seconds.Turbidity Sensor No SignalTurbidity sensor counter did not receive pulses from sensor.Turbidity Temp SensorTurbidity temperature sensor thermistor is shorted, open, or reading constant.UFOverfill conditionUpper ZoneInverter Error-Inverter not correctly actuating circulation pump (inverter power or…WASH (flashing)Value modelsWash BoostThermistor ErrorWash Boost LEDThermistor errorWASHING FLASHINGSTART/RESET pad has been pressed on Profile Performance models, indicating the dishwasher…WASHING_FLASH_BEEPControl error-the WASHING status light flashes accompanied by a beeping sound.WASHING_RINSING_FLASHSTART/RESET pad has been pressed

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.