Skip to main content
Error code reference
GE Range Error Codes
241 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
100Range miswired condition detected on 240VAC within first 10 minutes; monitoring is…200Cavity 1 thermal runaway when unlocked210Cavity 1 thermal runaway when locked300RTD1 sensor short-circuit detected (ADC value reads above 44268 counts).310RTD1 sensor open-circuit detected (ADC value reads below 19159 counts).331Open oven sensor detected; causes both cooktop and oven to become inoperative if stored…350Cooling fan speed fault351Cooling fan unexpected operation352Cooling fan rotor fault630Gen board 1 heartbeat missing640Gen board 2 heartbeat missing650Radiant board heartbeat missing682Left wing board UI heartbeat missing683Center UI board heartbeat missing684Right wing board UI heartbeat missing700Cavity 1 Cancel Off Monitor (UL)710Cancel Key Scanning Failed (RC15 Only)720Oven Stuck Key (RC15 Only)730Wing Board Knob 1 out of range731Wing Board Knob 2 out of range732Wing Board Knob 3 out of range733Wing Board Knob 4 out of range734Wing Board Knob 5 out of range735Wing Board Knob 6 out of range741Redundant ADC mismatch Wingboard Knob 1742Redundant ADC mismatch Wingboard Knob 2743Redundant ADC mismatch Wingboard Knob 3744Redundant ADC mismatch Wingboard Knob 4745Redundant ADC mismatch Wingboard Knob 5746Redundant ADC mismatch Wingboard Knob 6782UI Checks783UI Checks784UI Checks800Clean Two Step On Error Cavity 1810Cavity 1 heating element relay in unexpected state840Internal ADC diagnostic failure.900Cavity 1 door lock changed states unexpectedly.910Cavity 1 door lock failed to change to expected state.940Cavity 1 door detected as open when locked.960Cavity 1 door lock is in an unknown state.bAdThe installed electrical connection from the house to the unit is miswired (displayed as…bAd LinETerminal block cord miswire detectedbAd LinE bAdVoltage monitor error indicating a terminal block cord miswire; appears if 120VAC is not…C1Communication fail with Main Relay Board.C2Communication fail with Upper Temp Encoder.C3Communication fail with Upper Mode Encoder.C4Communication fail with AuxC5Communication fail with Lower Temp Encoder.C6Communication fail with Lower Mode Encoder.CLOSE DOORReminder message to keep the oven door closed during broil modeCONTROLControl lockout is activated; displayed with a lock symbol indicating oven controls are…CXCommunication error.DOORDoor not locked for clean cycle, did not unlock after clean, door not closed at power-up…DOOR LOCKThe self-clean cycle has been selected but the oven door is not closed; DOOR LOCK flashes…dorOven door was opened during the steam clean cycle.E011Stuck key on the cooktop control panel.E012Keyboard configuration error on the cooktop user interface board.E013Non-volatile memory alarm.E020Loss of communication from cooktop to oven control board.E022Loss of communication between generator board and user interface board.E035ON indicator display failure; the displays cannot show the LEDs properly, the mechanism…E051Unable to read cancel key / tail sense error.E126MACS communication mismatch (left generator board).E149Induction generator board configuration compatibility error (left generator board).E157MAIN (power supply) relay stuck on induction power board (left generator board).E158400V detection error on induction power board (left generator board).E159Too low main voltage detected on induction generator board (left generator board).E16115V power supply error on induction generator board (left generator board).E164Cooling fan on the induction generator board is blocked or otherwise unable to turn (left…E165Open temperature sensor on induction coil (left generator board).E167Loss of communication between control and power micros on induction generator board (left…E168Failure check found inconsistent voltage or current measurement between the two induction…E169Failure check found inconsistent voltage or current measurement between the two induction…E170Failure check found inconsistent power frequency detection between the two induction…E171Failure check found inconsistent power currents between the drive circuit for the coils…E172Internal syncing error between the two induction generator board microprocessors (left…E173Failure check found too-high temperature on induction generator board (left generator…E174Heat sink sensor open or shorted (left generator board).E175Failure check found a bad sensor or a shorted circuit on the induction generator board…E180Power supply and/or frequency lost on the induction generator board (left generator…E181Cooling fan not connected on induction generator board (left generator board).E226MACS communication mismatch (right generator board).E249Induction generator board configuration compatibility error (right generator board).E257MAIN (power supply) relay stuck on induction power board (right generator board).E258400V detection error on induction power board (right generator board).E259Too low main voltage detected on induction generator board (right generator board).E26115V power supply error on induction generator board (right generator board).E264Cooling fan on the induction generator board is blocked or otherwise unable to turn…E265Open temperature sensor on induction coil (right generator board).E267Loss of communication between control and power micros on induction generator board…E268Failure check found inconsistent voltage or current measurement between the two induction…E269Failure check found inconsistent voltage or current measurement between the two induction…E270Failure check found inconsistent power frequency detection between the two induction…E271Failure check found inconsistent power currents between the drive circuit for the coils…E272Internal syncing error between the two induction generator board microprocessors (right…E273Failure check found too-high temperature on induction generator board (right generator…E274Heat sink sensor open or shorted (right generator board).E275Failure check found a bad sensor or a shorted circuit on the induction generator board…E280Power supply and/or frequency lost on the induction generator board (right generator…E281Cooling fan not connected on induction generator board (right generator board).ERRCooktop lockout errorFFunction error code indicated by 'F' followed by a number or letter flashing in the…F- (number or letter)Function error code indicating a control or operational fault in the oven.F– (number or letter)Function error code indicating a fault condition in the oven control.F0Open OFF keyF001Touch failure on the oven user interface board.F002Touch failure on the oven user interface board.F003The oven user interface board is incorrectly configured.F004Touch failure on the oven user interface board.F005Touch failure on the oven user interface board.F010Oven temperature runawayF011Stuck keyF012Keyboard configuration alarmF013Data written to non-volatile memory has failed verification.F015Keyboard error.F017The oven user interface board is unable to configure the touch.F018Oven relay board failure (wiggler).F019The oven user interface board is unable to configure the oven relay board.F020Communication failure between the oven user interface board and the cooktop user…F022Communication failure between the oven user interface board and the oven relay board.F023Communication failure between the oven user interface microcontroller and the touch…F025The communication between the oven user interface and the oven relay board cannot be…F027The communication between the oven user interface and the oven relay board cannot be…F028The communication between the oven user interface microcontroller and the touch…F029The communication between the oven user interface microcontroller and the touch…F030Open oven temperature sensor (RTD).F031Shorted oven temperature probe (RTD).F033Meat probe temperature sensor shorted or too hot (triggered if meat probe sees…F050A/D Out of RangeF090Motor Door Lock mechanism failureF095Motor Door Lock mechanism failureF096The oven door has been detected open during a Self-Clean cycle.F097MDL invalid stateF098Magnetron case sensor probe shorted (NTC sensor on the magnetron has failed).F099Magnetron case sensor probe open (NTC sensor on the magnetron has failed).F1Control failureF10Runaway temperature; oven heats when no cook cycle is programmed.F100Magnetron case sensor temperature over-temp limit (NTC sensor on the magnetron detects…F101Magnetron auto power limit active based on temperature over-temp; magnetron self powered…F102Magnetron auto power limit active based on runtime limit exceeded; magnetron self powered…F104Loss of communication between GPU and OUI.F105Wake up procedure failure between OUI and GPU; the OUI can't communicate with the GPU at…F106GPU configuration error; the configuration on the GPU fails to startup.F107Loss of communication between OUI and NIU; the NIU stops communicating with the OUI.F108NIU provisioning failed (Connection Fail)F109OTA (over-the-air) update failed; the NIU is unable to complete an update over the…F11Shorted keypad or selector switch.F110NIU serialization failed (manufacturing error only, not at user end).F111Touch screen error from GPU; the GPU touch screen becomes irresponsive or malfunctions.F12EOC internal software error or failure.F13EOC internal software error or failure.F2Oven exceeded 590°F with door in unlocked position or exceeded 990°F with door lockedF20Communication failure between oven and cooktop control boards.F20xTemperature inside oven cavity exceeds 600°F with door unlocked.F21xTemperature inside oven cavity exceeds 900°F with door unlocked.F3Open oven temperature sensor circuit (over 2700 ohms) or shorted sensor circuit (under…F30Open oven sensor probe circuit.F30xShorted oven sensor (under 950 ohms).F31Shorted oven sensor probe circuit.F31xOpen oven sensor (over 2950 ohms).F32xTemperature measurement circuit redundancy check within Main Logic Board bad.F33xTemperature measurement circuit redundancy check within Main Logic Board bad.F4Open oven temperature sensor circuit (over 2700 ohms) or shorted sensor circuit (under…F40Communication failure between oven and cooktop control boards.F40xLIN comm error to/from RPSM Aux Board (when equipped).F45Cooling fan speed low in upper cavity (Microcombi will display F45 for lower cavity).F46Cooling fan speed high in upper cavity (Microcombi will display F46 for lower cavity).F47Cooling fan speed low in lower cavity.F48Cooling fan speed high in lower cavity.F5Control Sensor CircuitF6Problem within timekeeping circuits due to fluctuation of the 50 Hz power supply, or…F600LIN communication error within Main Logic Board.F610LIN communication error to slaves, such as RPSM.F611LIN communication error to slaves, such as RPSM.F612Line power error detected by RPSM.F620LIN communication error to/from RPSM AUX Board (when equipped).F621LIN communication error to/from RPSM AUX Board (when equipped).F622Line power error detected by RPSM.F640No LIN comm between Main Logic Board and Induction Bridge Board (when equipped).F7Shorted key detection except for slew entry and Clear/Off keysF70xCLEAR/OFF touch key error.F710Any other Touch Key error.F720Main Logic Board internal touch key chip signal error.F73060 Hz square wave not getting to touch key chip on Main Logic Board.F74060 Hz square wave not getting to touch key chip on Main Logic Board.F75060 Hz square wave not getting to touch key chip on Main Logic Board.F76060 Hz square wave not getting to touch key chip on Main Logic Board.F77060 Hz square wave not getting to touch key chip on Main Logic Board.F78060 Hz square wave not getting to touch key chip on Main Logic Board.F790Main Logic Board internal touch key chip signal error.F7A0Main Logic Board internal touch key chip memory error.F7B0Main Logic Board internal touch key chip memory error.F8Component failure within ERC affecting temperature processing circuitsF800Main Logic Board memory error.F810Main Logic Board memory error.F820Main Logic Board EEPROM memory error.F9Latch motor problemF90Door lock motor or latch circuit failure.F90xDoor Lock Unlock-Home signal became untrue during cooking.F91Door lock motor or latch circuit failure.F91xDoor Lock Unlock-Home signal became untrue during clean.F92Door lock motor or latch circuit failure.F92xBoth the Lock-Home and Unlock-Home switches are closed simultaneously.F93Door lock motor or latch circuit failure.F94Door lock motor or latch circuit failure.F95Door lock motor or latch circuit failure.FA00Device not found within Induction Cooktop module.FA10Induction cooktopFA30Induction cooktopFA40Induction cooktopFA47Enable signal not getting from Main Logic Board J241 pin 8 to Cooktop Bridge Board X200…FA5xInduction cooktop burner sensor too hot (F-code not logged).FA6xInduction cooktopFA7xInduction cooktop generator board temperature sensor open or DC problem.FA8xInduction cooktop communication error from cooktop filter to other cooktop boards.FA9xInduction cooktopFAAxInduction cooktopFCDoor Latch ErrorFDProbe failureFFControl senses oven temperature above 630°F with the door circuit in the unlock mode.FFFControl error, failed EEPROM.HOTOven temperature is above 52°C (125°F), preventing proofing mode from operatingLCSurface display indicates controls have been locked.LOCLockout valve position indicatorLOC OnControl lockout is active; all touch pads and cooktop controls are locked and cannot be…LOCKLock switch circuit open (flashing LOCK is normal condition while locking or unlocking)LOCK DOORThe self-clean cycle has been selected but the oven door is not closed, or the oven door…LOCK FLASHINGLock switch circuit is open (normal while locking/unlocking); may indicate open thermal…LOCKEDOven door is locked because the internal temperature has not dropped below the locking…LOCKED/DOOROven door is locked because the internal temperature has not dropped below the locking…LOW POWERPower monitor detects low power conditionPFPower failure indicationPrEOven is preheatingPrFProof mode is activeProbeThe probe is plugged into the oven outlet but no probe temperature has been set and START…SAbSabbath mode is active on the oven control.SFSpecial features mode entry confirmation displayed when Bake and Broil Hi/Lo pads are…Shut doorThe oven door is open during a cooking mode; message flashes on screen.SUPPLY MISWIREDPower monitor detects miswired supplySUPPLY OPEN NEUTRALPower monitor detects open neutralTURN BURNERS OFFA cooktop burner was on when the range was going into or out of self-clean modes.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.