mypros+
Error code reference

GE Range Error Code F8

Component failure within ERC affecting temperature processing circuits

GE codesGE range codes

Component failure within ERC affecting temperature processing circuits. An open circuit would indicate a defect in the touch pad.

First step from the service manual

Replace the ERC control.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F8.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F8 means on a GE range

The F8 error code on a GE range indicates an internal ERC (Electronic Range Control) fault detected by the control board itself. The ERC is the brain of the range, managing all cooking functions, keypad input, and component timing. When the control board detects an internal failure it cannot recover from, it throws F8 to signal that its own logic or memory has been compromised. This is not a sensor fault or a secondary component failure reported to the board; the board is reporting a problem within itself.

For homeowners, this means the electronic control board that runs your range has detected something wrong with its own internal circuitry. Think of it like a computer displaying a critical system error. The display may lock up, the range may stop responding to inputs, or it may shut down cooking functions entirely. The board is designed to fail safe and alert you rather than continue operating unpredictably.

A power reset clears temporary memory faults and is always the correct first step. If the F8 code returns after reconnecting power, the internal fault is persistent and the ERC itself must be replaced. No amount of resetting will correct a hardware failure within the control board's circuitry or corrupted non-volatile memory.

Source: manufacturer service documentation.

Common causes of F8

  1. 01

    Corrupted ERC internal memory

    Part replacement

    The control board's non-volatile memory can develop corrupted data due to power surges or age, causing persistent internal faults. A power reset clears volatile memory but cannot repair corrupted firmware storage within the ERC.

  2. 02

    Failed ERC internal circuitry

    Part replacement

    Physical failure of components on the control board, such as capacitors, voltage regulators, or processor circuits, will trigger an F8 that no reset can resolve. The board must be replaced when internal hardware has failed.

  3. 03

    Power surge damage to the ERC

    Part replacement

    A sudden voltage spike from the home electrical supply can damage the control board's internal components, causing it to log an unrecoverable internal fault on the next startup cycle.

  4. 04

    Intermittent power supply to the ERC

    Wiring / connection

    Loose wiring connections at the control board or an unstable power supply from the range's internal transformer can cause the ERC to misread its own status and log an F8. This may resolve with a power reset if the connection was only momentarily disrupted.

See the test procedure for each cause

Frequently asked questions about F8

What does the F8 error code mean on a GE range?
F8 on a GE range means the Electronic Range Control board has detected an internal fault within itself. This is not a problem with an external sensor or component; the ERC is reporting that its own circuitry or memory has failed. The first step is to disconnect power for one minute and reconnect. If F8 returns, the ERC must be replaced.
How do I fix the F8 error code on my GE range?
Start by unplugging the range or shutting off the circuit breaker for 60 seconds, then restore power. If F8 does not return, the fault was a temporary memory glitch. If F8 comes back immediately or after a short time, the Electronic Range Control board has a persistent internal failure and needs to be replaced. ERC replacement is a moderate DIY repair requiring basic electrical safety knowledge and the correct part number for your model.
Is it safe to use my GE range when F8 is displayed?
No. When F8 is active, the control board has detected an internal fault and the range should not be used for cooking. The ERC controls all heating elements and burner functions, and an internally faulted control board may behave unpredictably. Disconnect power until the fault is resolved.
How much does it cost to fix an F8 error on a GE range?
A replacement GE Electronic Range Control board typically costs between $150 and $350 depending on the specific model, with most parts available through GE Appliances Parts or third-party suppliers. If you hire a technician, expect to add $100 to $200 in labor. This repair is within reach for a confident DIYer comfortable working with appliance wiring, but if you are unsure about working near electrical connections in a range, a qualified appliance technician is the appropriate choice.
Will unplugging my GE range fix the F8 error?
Unplugging the range and restoring power is the correct first step for F8, and it does resolve the code if the fault was caused by a temporary power anomaly or memory glitch. However, if F8 returns after the power reset, the Electronic Range Control board has a hardware or persistent memory failure that a reset cannot fix, and the board must be replaced.

Related GE range codes

All GE range codes
View all 303 GE range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass