mypros+
Error code reference

GE Range Error Code F113

Runaway oven temperature exceeding 950°F with latch locked.

GE codesGE range codes

Runaway oven temperature exceeding 950°F with latch locked.

MyPros+ Max

Get the full diagnostic procedure for F113.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F113 means on a GE range

F113 is a runaway oven temperature fault that triggers when the oven cavity temperature exceeds 950°F while the door latch is in the locked position. This condition represents a critical thermal safety event. The control board monitors oven temperature continuously through the oven temperature sensor (RTD probe), and when readings climb beyond the 950°F threshold during a locked-door state, such as during or after a self-clean cycle, the control interprets this as an uncontrolled heating condition and sets the F113 fault to protect the appliance and surrounding cabinetry from heat damage.

The latch-locked context is significant because 950°F is a temperature that should only be approached during self-clean operation, and the control expects the heating elements to cycle off before temperatures reach dangerous extremes. If the bake or broil element fails in a shorted condition, or if the relay controlling that element welds closed on the control board, the element can continue drawing power without the control being able to shut it off. Simultaneously, a faulty oven temperature sensor that reads artificially low can prevent the control from recognizing how hot the cavity has actually become, allowing temperatures to climb unchecked.

Because this fault involves both extreme heat and a locked door, it carries a real safety concern. The oven should be powered off at the circuit breaker immediately if the fault appears during active heating. Once the unit has cooled completely, diagnosis should focus on the oven temperature sensor resistance, the condition of the bake and broil elements, and the relay outputs on the electronic control board.

Source: manufacturer service documentation.

Common causes of F113

  1. 01

    Welded relay on the control board

    Part replacement

    A relay on the electronic control board can weld shut in the closed position, causing the bake or broil element to receive continuous power with no way for the control to shut it off. This results in uncontrolled temperature rise and is one of the most common causes of runaway oven faults.

  2. 02

    Faulty oven temperature sensor

    Part replacement

    If the RTD temperature sensor has drifted out of calibration or has failed with a resistance reading that is too high, the control board receives artificially low temperature data and does not recognize when the oven has exceeded safe limits. The sensor should be tested for proper resistance at room temperature and compared against specification.

  3. 03

    Shorted bake or broil element

    Part replacement

    A bake or broil element that has developed an internal short can draw power continuously even when the control attempts to de-energize it. Visual inspection may reveal burn marks, blistering, or a visible break point with arc damage on the element surface.

  4. 04

    Damaged door latch assembly

    Part replacement

    If the latch motor or latch switch is malfunctioning, the control board may receive an incorrect signal indicating the door is locked when it is not, or may fail to release the latch at the end of a self-clean cycle, pairing a latch-locked status with a thermal fault condition.

  5. 05

    Electronic control board failure

    Part replacement

    Beyond welded relays, broader failure of the control board logic can cause it to misinterpret sensor data, fail to cycle heating elements correctly, or become unable to terminate a self-clean cycle at the appropriate temperature.

See the test procedure for each cause

Frequently asked questions about F113

What does F113 mean on a GE range?
F113 indicates that the oven temperature exceeded 950°F while the door latch was in the locked position, signaling a runaway heating condition. This fault is most commonly triggered during or after a self-clean cycle. It points to a problem with the control board relays, the oven temperature sensor, or the heating elements that is preventing the oven from regulating heat properly.
Is it safe to use my GE range when F113 is displayed?
No, the range should not be used while this fault is active. An F113 fault indicates a potential runaway heating situation, which is a fire and damage risk. Turn the range off at the wall circuit breaker immediately and leave it off until the underlying cause has been diagnosed and repaired by a qualified technician.
Will resetting the power clear the F113 error code on a GE range?
Resetting the breaker may temporarily clear the fault code, but it will not resolve the underlying problem. If the component causing uncontrolled heating, such as a welded relay, a failed temperature sensor, or a shorted element, is still present, the fault will return and the dangerous condition will persist. A reset should only be performed as part of a diagnostic process, not as a fix.
How do I fix an F113 error on a GE range?
Diagnosis should begin after the oven has cooled completely with power off at the breaker. Check the oven temperature sensor for correct resistance and inspect the bake and broil elements for visible damage. If the elements and sensor test acceptable, the electronic control board, specifically its output relays, is the likely culprit. Depending on which component has failed, the repair will involve replacing the sensor, one or both elements, the door latch assembly, or the control board.
How much does it cost to repair a GE range showing F113?
Repair costs vary depending on the failed component. An oven temperature sensor is typically the least expensive part, while an electronic control board is at the higher end of the repair cost range. Including labor, total repair costs can range from roughly $150 to $500 or more depending on the part required and local service rates. Getting a diagnostic service call with a written estimate before authorizing parts replacement is recommended.

Related GE range codes

All GE range codes
View all 303 GE range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass