mypros+
Error code reference

GE Range Error Code F4 E0

Meat probe shorted (less than 1500 ohms).

GE codesGE range codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F4 E0 error code actually means

Your GE range is detecting a problem with the meat probe, the thermometer-style accessory you insert into food while it cooks in the oven. The probe is sending a signal that indicates it has an internal short, which means it is likely damaged and needs to be replaced. Unplugging the probe and trying a new one is the recommended first step to resolve this issue.

Diagnostic procedure

The full F4 E0 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace meat probe.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F4 E0 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F4 E0

Ranked by how often they cause this code
  1. 1Failed or damaged meat probe
  2. 2Damaged probe cable
  3. 3Contaminated probe connector jack
  4. 4Faulty probe receptacle or wiring
  5. 5Oven control board fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F4 E0

What does F4 E0 mean on a GE range?
F4 E0 means the oven control has detected a shorted meat probe circuit, with resistance reading below 1500 ohms. The meat probe is the food temperature sensor that plugs into the side wall of the oven cavity. This code indicates the probe or its associated wiring is creating an abnormally low-resistance path, which the control interprets as a fault.
How do I fix the F4 E0 error on my GE range?
Start by unplugging the meat probe from the oven's probe jack and inspecting the probe and its cable for visible damage. Replace the meat probe with a compatible unit and test the oven. If the error persists after installing a new probe, inspect the probe receptacle and wiring, and consider having the control board evaluated.
How much does it cost to fix a GE range F4 E0 error?
If the meat probe itself is the cause, replacement probes typically cost between $20 and $60 depending on the model. If the wiring harness or receptacle requires repair, labor costs from a technician may add $75 to $150 or more. A control board replacement, if needed, is the most expensive scenario and can range from $150 to $350 or higher for parts alone.
Will resetting my GE range clear the F4 E0 error?
Resetting the range by cutting power at the breaker may temporarily clear the display, but F4 E0 will return if the underlying short in the meat probe circuit is still present. A permanent fix requires addressing the root cause, typically by replacing the meat probe. Reset alone is not a solution.
Is it safe to use my GE range while it shows F4 E0?
The F4 E0 code is specific to the meat probe circuit and does not directly affect basic oven or burner operation. However, the probe temperature monitoring function will not work correctly while the fault is active. It is advisable to disconnect and remove the meat probe and avoid using probe-based cooking modes until the issue is resolved.

Related GE range error codes

All GE range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass