mypros+
Error code reference

GE Range Error Code F3 E7

Warming drawer sensor shorted.

GE codesGE range codes

Warming drawer sensor shorted.

First step from the service manual

Unplug range or disconnect power, open back panels and verify the warming drawer sensor is plugged in.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F3 E7.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F3 E7 means on a GE range

The F3 E7 error code on a GE range indicates that the warming drawer temperature sensor has developed a short circuit condition. The control board continuously monitors resistance from the warming drawer sensor to determine the drawer's temperature. When that resistance reading drops below the expected range for any valid temperature, the board interprets the signal as a shorted sensor and triggers this fault code. A shorted sensor typically reads near zero ohms rather than the several thousand ohms expected from a functioning thermistor.

The warming drawer sensor is a thermistor located inside or immediately adjacent to the warming drawer cavity. It connects to the main control board via a wiring harness that runs through the back of the range. The most common causes of this fault are a damaged sensor element, a pinched or chafed wire harness creating a direct short to ground, or a connector that has been pushed together incorrectly, bridging two terminals.

The first diagnostic step is to unplug the range or disconnect power at the breaker, then open the back panels to access the wiring harness and verify the warming drawer sensor connector is fully and correctly seated. A loose or improperly connected plug can mimic a short condition and is the simplest fix to rule out. If the connector appears correct, the sensor's resistance should be measured directly at the sensor terminals and compared against the expected value for the ambient temperature. A reading near zero ohms confirms the sensor has failed internally and requires replacement.

Source: manufacturer service documentation.

Common causes of F3 E7

  1. 01

    Disconnected or improperly seated sensor connector

    Wiring / connection

    The sensor wiring connector at the back of the range may have come loose or been plugged in incorrectly, causing a false short reading. Unplugging and firmly reseating the connector is the first step to rule this out.

  2. 02

    Failed warming drawer sensor (thermistor)

    Part replacement

    The thermistor element inside the sensor can fail internally and short to near zero ohms resistance, which the control board reads as a fault. Measuring resistance across the sensor terminals will confirm this if the reading is near zero.

  3. 03

    Pinched or damaged wiring harness

    Part replacement

    The wire harness running from the warming drawer sensor to the control board can become pinched, chafed, or damaged over time, creating a short circuit between conductors or to the chassis ground. Inspect the harness along its entire length for visible damage or contact points.

  4. 04

    Corroded or shorted connector terminals

    Part replacement

    Moisture or heat exposure can cause corrosion or carbon buildup inside the sensor connector, bridging terminals and creating a short condition. Inspect the connector pins closely for discoloration, residue, or physical damage.

  5. 05

    Faulty main control board

    Part replacement

    If the sensor and all wiring test correctly, the control board's sensor input circuit may have failed and is misreading the signal. This is the least likely cause and should only be considered after the sensor and harness have been fully ruled out.

See the test procedure for each cause

Frequently asked questions about F3 E7

What does F3 E7 mean on a GE range?
F3 E7 on a GE range means the control board has detected a short circuit in the warming drawer temperature sensor circuit. The sensor, also called a thermistor, is reading a resistance value outside the expected range, which indicates a shorted condition. This prevents the control system from accurately monitoring the warming drawer's temperature.
Can I fix the F3 E7 error code myself?
Yes, some causes of F3 E7 are DIY-friendly. Start by unplugging the range, removing the back panel, and checking that the warming drawer sensor connector is properly seated. If the connector looks fine, a technician or experienced DIYer can use a multimeter to test the sensor's resistance and determine whether the sensor or wiring needs to be replaced.
Is it safe to use my GE range while it shows the F3 E7 code?
The F3 E7 code specifically affects the warming drawer circuit, so the main oven and cooktop burners may continue to operate. However, the warming drawer should not be relied on while this fault is active since its temperature is not being properly monitored. Addressing the fault promptly is recommended to avoid any unintended behavior from the control board.
Will resetting the range clear the F3 E7 error code?
Resetting the range by unplugging it or cycling the breaker may temporarily clear the error display, but the code will return if the underlying problem with the warming drawer sensor or its wiring has not been corrected. A reset alone does not fix the shorted sensor condition.
How much does it cost to repair a GE range showing F3 E7?
If only the warming drawer sensor needs replacement, parts typically cost in the range of $20 to $60 depending on the model. If a technician is needed for diagnosis and installation, total repair costs including labor generally fall in the range of $100 to $250. A main control board replacement, if required, can push costs higher, often in the range of $200 to $400 or more with labor.

Related GE range codes

All GE range codes
View all 303 GE range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass