mypros+
Error code reference

GE Range Error Code F5E6

Door locked somehow with door open.

GE codesGE range codes

Door locked somehow with door open.

First step from the service manual

Check door switch, latch switch.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F5E6.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F5E6 means on a GE range

The F5E6 error code on a GE range indicates a conflict between the door lock mechanism and the door position sensors. Specifically, the control board has detected that the door lock is engaged while the door position switch is reporting the door as open. This is a logical contradiction: the locking mechanism should only engage when the door is fully closed and latched, typically during a self-clean cycle. When these two signals disagree, the board flags the fault to prevent unsafe operation of the locking system.

The two primary components involved are the door switch and the latch switch. The door switch tells the control board whether the oven door is physically open or closed. The latch switch reports the position of the locking motor and latch assembly, indicating whether the door lock is retracted, in motion, or fully engaged. If either of these switches fails, sends an incorrect signal, or has wiring that is damaged or corroded, the control board can receive mismatched status information and trigger F5E6.

Common root causes include a faulty door switch that falsely reports the door as open while the latch has already engaged, a stuck or mechanically jammed latch assembly that remains in the locked position after a self-clean cycle, or wiring harness issues between the switches and the control board. In some cases, a failed control board may misinterpret valid switch signals, though this is less common than a mechanical or switch-level fault.

Source: manufacturer service documentation.

Common causes of F5E6

  1. 01

    Faulty door latch switch

    Part replacement

    The latch switch may be stuck in the locked position or sending a false locked signal even when the latch has retracted. This is the most common trigger for F5E6 and can be identified by inspecting whether the latch assembly moves freely and by checking switch continuity with a multimeter.

  2. 02

    Faulty door switch

    Part replacement

    The door switch may be failing to correctly report the door position to the control board, causing it to signal that the door is open when the latch is engaged. Testing the switch for proper continuity when the door is opened and closed will confirm whether it is functioning correctly.

  3. 03

    Mechanically stuck or jammed latch assembly

    Part replacement

    The physical latch mechanism can become jammed in the locked position, particularly after a self-clean cycle due to heat stress or debris. If the latch motor runs but the latch does not retract fully, the switch signals will conflict and trigger this code.

  4. 04

    Damaged or corroded wiring harness

    Wiring / connection

    Wiring between the door switch, latch switch, and control board can suffer from heat damage, pinching, or corrosion, especially near the oven door hinge area. Inspect the harness for visible damage, loose connectors, or broken terminals that could cause intermittent or false signals.

  5. 05

    Failed control board

    Part replacement

    If the door switch and latch switch both test correctly and the wiring is intact, the control board itself may be misreading the input signals. A board fault is the least common cause but should be considered after all other components have been ruled out.

See the test procedure for each cause

Frequently asked questions about F5E6

What does F5E6 mean on a GE range?
F5E6 on a GE range means the control board has detected a conflict between the door lock and the door position sensor. The system is seeing a locked door condition at the same time it receives a signal that the door is open, which is a contradiction. This typically points to a problem with the door switch, the latch switch, or the wiring connecting them to the board.
Can I fix the F5E6 error myself?
Some causes of F5E6 are DIY-friendly if you are comfortable with basic appliance repair. You can inspect the latch assembly for visible jams, check wiring connectors for looseness or damage, and test the door switch and latch switch for proper continuity using a multimeter. If a switch needs replacement, that is a straightforward repair for most experienced DIYers. If the control board is the issue, replacement is more involved and may warrant professional service.
Is it safe to use my GE range while F5E6 is displayed?
You should not continue using the range while F5E6 is active. This error involves the door locking system, and a stuck or malfunctioning latch could present a hazard, particularly if it triggers unexpectedly during operation. It is best to resolve the fault before using the oven again, especially the self-clean function.
Will resetting the range clear the F5E6 error?
A power reset, done by unplugging the range or flipping the circuit breaker for one to two minutes, may temporarily clear the F5E6 code. However, if the underlying issue with the door switch, latch switch, or wiring is not corrected, the error will return. A reset is useful for ruling out a transient glitch but is not a permanent fix.
How much does it cost to repair a GE range F5E6 error?
Repair costs vary depending on the failed component. A replacement door switch or latch switch typically costs in the range of $15 to $60 for parts, while a latch motor assembly can run $40 to $120. If professional labor is needed, expect additional costs of $100 to $200 or more depending on your area. A control board replacement is the most expensive scenario, with parts potentially ranging from $150 to $350.

Related GE range codes

All GE range codes
View all 303 GE range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass