mypros+
Error code reference

GE Range Error Code F160

Cooling fan hall effect feedback not present (NTC temp in built-in range only).

GE codesGE range codes

Cooling fan hall effect feedback not present (NTC temp in built-in range only).

MyPros+ Max

Get the full diagnostic procedure for F160.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F160 means on a GE range

The F160 error code on a GE built-in range indicates that the control board is not receiving hall effect feedback from the cooling fan motor. The cooling fan is responsible for protecting the electronics and surrounding cabinetry from heat buildup during and after cooking. In built-in range models, this error is specifically tied to NTC (negative temperature coefficient) temperature sensing, meaning the system monitors both the fan's rotational feedback signal and the thermal environment around the electronics enclosure.

Hall effect sensors work by detecting the rotation of a magnet embedded in or attached to the fan motor shaft. As the fan spins, the sensor generates a pulse signal that the control board uses to confirm the fan is operating. If that signal is absent, the board cannot verify fan operation and triggers F160. This failure can stem from a dead fan motor, a broken or disconnected hall effect sensor, wiring harness faults between the fan assembly and the control board, or a failed control board that cannot interpret the signal even if it is present.

Because this fault involves active cooling of the electronics, the range may limit or disable operation while the error is active to prevent heat damage to internal components. Technicians should inspect the fan assembly for physical obstructions, test the motor for continuity, and verify signal integrity at the harness connectors before condemning the control board. The NTC thermistor in the cooling circuit should also be checked for correct resistance values if the fan and wiring test normal.

Source: manufacturer service documentation.

Common causes of F160

  1. 01

    Failed cooling fan motor

    Part replacement

    The fan motor itself may have burned out or seized, preventing rotation entirely. Inspect the fan blade for obstructions and test the motor windings for continuity.

  2. 02

    Faulty hall effect sensor

    Part replacement

    The hall effect sensor on the fan assembly may have failed and is no longer generating the rotation feedback pulse the control board expects. This can occur even if the fan motor is still spinning.

  3. 03

    Wiring harness damage or loose connector

    Wiring / connection

    The wiring between the fan assembly and the control board may have a broken wire, burned connector, or loose pin that interrupts the feedback signal. Inspect all connectors and harness routing near heat sources.

  4. 04

    NTC thermistor failure

    Part replacement

    In built-in range models, the NTC temperature sensor in the cooling circuit may have drifted out of range or failed open, contributing to the fault condition. Check resistance values at the thermistor and compare to specification.

  5. 05

    Failed control board

    Part replacement

    If the fan motor, hall effect sensor, NTC thermistor, and all wiring test correctly, the control board may be unable to process the incoming feedback signal. This is the least likely cause and should be diagnosed last.

See the test procedure for each cause

Frequently asked questions about F160

What does F160 mean on a GE range?
F160 on a GE range means the control board is not receiving the expected hall effect feedback signal from the cooling fan motor. This code applies specifically to built-in range models and also involves the NTC temperature sensor in the cooling system. The range uses this fan to protect internal electronics from heat, and the error is triggered when the board cannot confirm the fan is spinning. The range may restrict operation until the fault is resolved.
Can I reset the F160 error code on my GE range and keep using it?
Resetting the range by cutting power may temporarily clear the F160 code, but if the underlying cause is not repaired, the error will return. Because this fault involves the cooling fan that protects the electronics, continuing to use the range without a working cooling fan risks heat damage to the control board and other internal components. A reset is acceptable for initial diagnostics, but should not be used as a long-term workaround.
Is it safe to use my GE range when F160 is displayed?
Using the range with an active F160 error is not recommended. The cooling fan is designed to protect the electronics from heat buildup during and after cooking cycles. Operating without confirmed fan function increases the risk of overheating the control board and other internal parts, which can lead to more extensive damage or create a safety concern.
How do I fix the F160 error on a GE range?
Fixing F160 requires identifying the specific failed component in the cooling fan circuit. Start by inspecting the fan for physical obstructions and testing the motor for continuity. Next, check the hall effect sensor and the wiring harness connectors between the fan and control board. On built-in models, the NTC thermistor in the cooling circuit should also be tested. If all these components check out, the control board may need to be replaced.
How much does it cost to repair the F160 error on a GE range?
Repair costs for F160 depend on which component has failed. A cooling fan motor or hall effect sensor assembly typically runs in the range of $40 to $150 in parts, while a control board replacement can cost $150 to $400 or more depending on the model. Adding labor from a qualified technician will increase the total. Getting a diagnostic visit first is the most cost-effective approach before ordering parts.

Related GE range codes

All GE range codes
View all 303 GE range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass