mypros+
Error code reference

GE Dishwasher Error Code PF RESET

Electrical power to the dishwasher has been interrupted but is now back on.

GE codesGE dishwasher codes

Electrical power to the dishwasher has been interrupted but is now back on.

First step from the service manual

Press the RESET pad and wait approximately 30 seconds, then unlatch and open the door to check detergent cup status and reprogram cycle as needed.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for PF RESET.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What PF RESET means on a GE dishwasher

The PF RESET code on a GE dishwasher indicates that electrical power to the unit was interrupted at some point during operation and has since been restored. PF stands for Power Failure. When the dishwasher loses power mid-cycle, whether due to a tripped circuit breaker, a momentary utility outage, or a disconnected power supply, the control board loses its active cycle memory. Upon power restoration, the dishwasher displays this code to alert the user that the previous cycle did not complete as programmed.

The control board is the primary system involved in this condition. It monitors power continuity and stores the active wash cycle state in volatile memory. When power is cut, that memory is cleared, and the board cannot resume the interrupted cycle automatically. This is a normal protective behavior rather than a component failure. The dishwasher requires manual intervention to confirm the current state of the wash and to restart if needed.

Because power was interrupted mid-cycle, there are several practical concerns to address before restarting. The detergent dispenser cup may have already opened and released detergent, or it may still be closed and loaded. Pressing the RESET pad and waiting approximately 30 seconds allows the control board to complete its reset sequence. Opening the door after that interval lets the technician or user inspect the dispenser cup status and determine whether a full cycle needs to be reprogrammed from the beginning.

Source: manufacturer service documentation.

Common causes of PF RESET

  1. 01

    Momentary power outage or utility interruption

    Wiring / connection

    A brief loss of household power from the utility grid is the most frequent trigger for this code. Even a fraction-of-a-second interruption is enough to clear the control board's cycle memory.

  2. 02

    Tripped circuit breaker

    Wiring / connection

    A tripped breaker on the dishwasher's dedicated circuit will cut power entirely. Check the electrical panel for a breaker in the tripped position and reset it before attempting to restart the dishwasher.

  3. 03

    Loose or intermittent power connection

    Wiring / connection

    A loose connection at the wall outlet, the junction box, or the power cord terminals can cause intermittent power interruptions. Inspect the power supply connection points for secure, corrosion-free contacts.

  4. 04

    Someone pressing the power button or opening the door mid-cycle

    Wiring / connection

    Accidentally pressing the power button or a switch on the circuit during a wash cycle will trigger this code when power is restored or the unit is turned back on. This is a user-initiated interruption rather than an electrical fault.

  5. 05

    Failing control board with poor power regulation

    Part replacement

    In rare cases, an aging or damaged control board may drop power internally, mimicking an external outage. If PF RESET appears repeatedly without any external power events, the control board may need inspection and possible replacement.

See the test procedure for each cause

Frequently asked questions about PF RESET

What does PF RESET mean on a GE dishwasher?
PF RESET indicates that electrical power to the dishwasher was interrupted while it was running and has since been restored. PF stands for Power Failure. The dishwasher displays this code because its control board lost the active cycle data when power was cut. You need to reset the unit and reprogram the wash cycle before running it again.
How do I fix the PF RESET code on my GE dishwasher?
Press the RESET pad and wait approximately 30 seconds to allow the control board to complete its reset sequence. Then unlatch and open the door to inspect the detergent dispenser cup. If the cup is still closed and loaded, the detergent was not dispensed, so you can reprogram and restart the full cycle. If the cup is open, detergent was already released and you may need to add fresh detergent before restarting.
Is the PF RESET code a sign that something is broken on my GE dishwasher?
In most cases, no. PF RESET is a notification code rather than a fault code, and it typically means an external power interruption occurred rather than an internal component failure. If the code appears only once after a known outage or tripped breaker, the dishwasher is functioning normally. If PF RESET appears repeatedly without any clear external cause, it may be worth checking the power supply connection or evaluating the control board.
Will resetting the dishwasher clear the PF RESET code?
Yes. Pressing the RESET pad and waiting approximately 30 seconds will clear the PF RESET display and return the control board to a ready state. After the reset is complete, open the door to check the detergent cup and then select and start a new cycle. No additional steps are required unless the code returns without explanation.
How much does it cost to repair a GE dishwasher showing PF RESET?
In most situations, PF RESET requires no repair and no parts because it results from an external power interruption. If a tripped breaker or loose connection is responsible, the fix is typically free or very low cost. If the control board is found to be faulty and requires replacement, repair costs including parts and labor generally range from around $150 to $400 or more depending on the model and service rates in your area.

Related GE dishwasher codes

All GE dishwasher codes
View all 222 GE dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass