mypros+
Error code reference

GE Dishwasher Error Code STATUS

Control error

GE codesGE dishwasher codes

Control error - all status lights flash accompanied by a beeping sound, indicating a control malfunction.

First step from the service manual

Press the START/RESET pad to turn off the beeper and the dishwasher will attempt to reset. Then restart the wash cycle. If this error continues, call for service.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for STATUS.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What STATUS means on a GE dishwasher

The STATUS error on a GE dishwasher is a control malfunction indication. When this condition occurs, all status lights on the control panel flash simultaneously while the unit emits a continuous or repetitive beeping sound. This behavior signals that the main control board has encountered an internal fault it cannot self-resolve during normal operation. The control board is the central processing unit of the dishwasher, managing cycle timing, water fill, heating, and drain functions. When it loses its operational logic or receives conflicting signals, it enters this alert state to notify the user that normal cycle execution cannot continue.

The most common trigger for this error is a temporary communication or logic fault within the control board, which is why the first recommended step is a soft reset using the START/RESET pad. Pressing this pad signals the controller to halt the current operation, silence the beeper, and attempt to reinitialize its internal processes. If the underlying issue was a transient voltage spike, power fluctuation, or momentary software glitch, the reset will often allow the dishwasher to restart and complete a cycle normally.

If the STATUS error returns after the reset attempt and a new cycle is started, the fault is considered persistent. Persistent control errors typically point to a failing or failed main control board, a wiring harness issue affecting the board's inputs or outputs, or a component fault that the board is detecting and flagging. At that point, further diagnosis requires hands-on inspection and the control board or related components may need to be tested or replaced.

Source: manufacturer service documentation.

Common causes of STATUS

  1. 01

    Transient control board fault

    Wiring / connection

    A temporary voltage spike or power fluctuation can cause the control board to lose its logic state and trigger the STATUS error. This type of fault often clears after pressing START/RESET and allowing the dishwasher to reinitialize.

  2. 02

    Failed or failing main control board

    Part replacement

    If the STATUS error returns consistently after resets, the control board itself may have a failed component or corrupted firmware. The board would need to be inspected and likely replaced to restore normal function.

  3. 03

    Loose or damaged wiring harness connection

    Wiring / connection

    A loose connector or damaged wire leading to or from the control board can cause erratic signals that trigger a control fault. Inspecting the harness connections at the control board for corrosion, looseness, or damage can identify this issue.

  4. 04

    Power supply irregularity

    Wiring / connection

    Unstable household voltage or a weak connection at the dishwasher's power supply can cause the control board to behave erratically and flag a control error. Checking the outlet voltage and the dishwasher's power connection can help rule this out.

  5. 05

    Faulty door latch or door switch

    Part replacement

    If the door latch assembly or its associated switch is sending an incorrect signal to the control board, the board may interpret this as a system conflict and enter the STATUS fault state. Inspecting the latch for physical damage or misalignment is a useful diagnostic step.

See the test procedure for each cause

Frequently asked questions about STATUS

What does STATUS mean on a GE dishwasher?
The STATUS error on a GE dishwasher means the main control board has detected a malfunction and cannot continue normal operation. It is indicated by all status lights flashing at the same time along with a beeping sound. This is essentially a catch-all control fault signal telling the user that the electronics need attention. It may be caused by something as simple as a temporary power glitch or as serious as a failed control board.
Will pressing START/RESET fix the STATUS error on my GE dishwasher?
Pressing the START/RESET pad is the first recommended step and will sometimes resolve the error if it was caused by a temporary glitch. The dishwasher will silence the beeper and attempt to reset its internal control logic. If the error does not return after restarting the wash cycle, the fix was successful. However, if the STATUS error comes back, the problem is persistent and will require a service technician to diagnose and repair.
Is it safe to use my GE dishwasher when the STATUS error is showing?
When the STATUS error is active, the dishwasher is not operating and has halted its cycle, so there is no immediate safety hazard from continuing to use water or heat. However, you should not attempt to force the dishwasher to run through a fault condition repeatedly. Try the reset procedure once, and if the error persists, stop using the appliance and call for service to avoid any risk of worsening the underlying electrical issue.
How much does it cost to repair a GE dishwasher STATUS control error?
Repair costs depend on the root cause identified during diagnosis. If the issue is a loose wiring connection, the cost may be limited to a service call fee, typically in the range of $75 to $150. If the main control board needs to be replaced, parts and labor combined can range from $200 to $450 or more depending on the specific model and local labor rates. Getting a diagnostic assessment from a qualified technician before committing to repairs is recommended.
Why does the STATUS error keep coming back on my GE dishwasher after I reset it?
A recurring STATUS error after multiple resets indicates that the underlying fault has not been resolved by the reset procedure alone. This typically points to a hardware problem such as a failing main control board, a damaged wiring harness, or a component that the board is continuously detecting as faulty. Repeated resets will not fix a hardware failure. At this stage, the dishwasher requires hands-on diagnostic work by a repair technician to identify and replace the defective component.

Related GE dishwasher codes

All GE dishwasher codes
View all 222 GE dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass