Model reference
GE PDT
Dishwasher
17 documents28 error codes39 service modes
Available documentation
Service Manual
- GE Appliances Technician's Manual GE Built-in Dishwashers Generation II14 pg
- GE Profile™ Dishwasher Technical Service Guide37 pg
- Manuel du propriétaire - Lave-vaisselle GE Profile24 pg
- TECHNICAL SERVICE GUIDE Top Control Profile Dishwashers27 pg
- Technical Service Guide "2" Model Dishwashers31 pg
- TECHNICAL SERVICE GUIDE Profile Dishwashers34 pg
- GE Appliances Technical Service Guide - GE and Profile Dishwashers PermaTuf® Tub Models and Stainless Steel Tub Models40 pg
- GE and Profile Dishwashers Technical Service Guide40 pg
- GE and Profile Dishwashers PermaTuf Tub and Stainless Steel Tub Technical Service Guide40 pg
- GE Consumer & Industrial Technical Service Guide - GE Profile Dishwasher PDW8900 Series, PDW9700 Series, PDW9900 Series37 pg
- GE Profile TM Dishwasher Technical Service Guide37 pg
- TECHNICAL SERVICE GUIDE Profile Dishwashers35 pg
- GE Profile Dishwashers Owner's Manual48 pg
- GE Profile Dishwashers Owner's Manual16 pg
- Dishwashers Triton™ Profile™ Owner's Manual32 pg
Training
- 2012 and Later Plastic Tub and Stainless Steel Tub Dishwashers Diagnosing UI (User Interface) Controls3 pg
- TECHNICAL SERVICE GUIDE MODEL DISHWASHERS Profile Performance Series31 pg
MyPros+ Max
Diagnose your GE PDT.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (28)
CodeMeaning
ALL_FLASH_BEEPControl error indicated by all status lights (SENSING, WASHING, RINSING…C1Slow drain fault detected; pump out time is over 100 seconds.C2Pump out time is more than 400 seconds; control stops the pump for 5 seconds…C3Control does not sense the drain feedback signal; control will default to…C4Control detects a flood condition within the dishwasher; control will beep at 1…C5Control detects two consecutive pump out times of less than 6 seconds…C6Water temperature did not reach 120°F during the main wash; fault continues to…C7Control checks the temperature sensor at start of each wash cycle to determine…CLEAN flashingUnit has no water; the water supply may be off or there is a water supply issue.CLEAN flashing (alone)Unit has no waterDRYING FLASHINGControl error on Profile Performance models indicated by flashing DRYING LED…F0Turbidity sensor failureF1Turbidity sensor failureF4Turbidity sensor failureLock LED + continuous beepFactory Test Mode calibration failureLOCK LED illuminated + continuous beeping (Factory Test Mode)Turbidity sensor check has failed during factory test mode; control module…NORMAL FLASHINGControl error on Profile models indicated by flashing NORMAL LED and beeping…PFElectrical power has been interrupted to the dishwasher; PF comes up in the…RINSING FLASHINGControl error on Profile Performance models indicated by flashing RINSING LED…RINSING_FLASHControl error indicated by the RINSING status light flashing along with a…SENSINGCleanSensor errorSensing LED not litTurbidity sensor circuit has failed open or is shorted; unit will operate for…SENSING OFFCleanSensor errorSTART RESET FLASHINGNormal indication on Profile models that the START/RESET pad has been pressed…START/RESET flashingCycle has been interrupted by pressing the START/RESET keypad; light will quit…START/RESET flashing + CLEAN flashingCycle has been interrupted by pressing the START/RESET keypad; light will quit…WASHING FLASHINGSTART/RESET pad has been pressed on Profile Performance models, indicating the…WASHING_RINSING_FLASHSTART/RESET pad has been pressedService modes (39)
- Consumer Purge Cycle1. Make sure Pre-wash, Added Heat, and Heated Dry LEDs are off. 2. Press Heated Dry pad and…
- Control lock["Press and hold HEATED DRY button for 3 seconds
- Control Panel Lock/Unlock["Press and hold the HEATED DRY pad for 3 seconds to lock the controls (light above LOCK pad will…
- Control Replacement/Calibration (test/00 calibration mode)["The dishwasher will enter into the test/00 calibration mode when the unit is first powered…
- control_replacement_calibrationThe dishwasher will enter into the test/00 calibration mode when the unit is first powered on
- Demo ModePress the Cookware pad (Down arrow on Top Control models) and Added Heat pad simultaneously for 5…
- End-of-cycle beep toggle["Press HEATED DRY button 5 times within 3 seconds.","Three beeps will sound to indicate the…
- F.I Test (Smart Models)["1
- F.I Test (Value Models)["1
- F1 Test Cycle["Close detergent cup and add hot water.","Press POTS & PANS and NORMAL WASH keypads at the same…
- F1 Test Freeze Capability["While F1 test cycle is running, press the HEATED DRY keypad to pause on the current test…
- Factory Test ModeDisconnect power from dishwasher
- Factory Test Mode (Front Control)["Enter Service Mode.","Press Key#5 and Key#1 together for 3 seconds.","This sets auto FE Entry…
- Factory Test Mode (Top Control)["Enter Service Mode.","Press Heated Dry and Delay Hours together for 3 seconds.","This sets auto…
- factory_test_mode_entry_flagFront control models
- Fast Control Model Reset["Make sure the unit is powered off.","Press and hold the Start/Reset keypad and power the unit…
- fast_control_model_reset1
- Freeze Capability (during F.I Test)["During the F.I test cycle, press the LOCK pad to pause.","Press any pad to continue."]
- LOW DETERGENT indicator toggle["Press ADDED HEAT button 5 times within 3 seconds.","Three beeps will sound and the LOW DETERGENT…
- Service ModePDW8900 Series
- Service Test Mode["Put the dishwasher in standby mode.","On front control models, press Key#8 and Key#4…
- service_test_mode1
- SmartDispense Water Hardness Calibration["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
- SmartDispense water hardness calibration (12-button front panel with 3-digit display)["Close and lock the door (lights on, dishwasher at rest).","Press COOKWARE and DELAY HOURS buttons…
- SmartDispense Water Hardness Calibration (12-Button Front-Control Models With 3-Digit Display)["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
- SmartDispense water hardness calibration (7-button front panel with 3-digit display)["Open the door and press any button (other than START) to activate the lights.","Press Up arrow…
- SmartDispense Water Hardness Calibration (7-Button Front-Control Models With 3-Digit Display)["Open the door and touch a pad (other than START) to turn lights on.","Press the Up Arrow Pad and…
- SmartDispense water hardness calibration (models without 3-digit display, front controls)["Close and lock the door (lights on, dishwasher at rest).","Press COOKWARE and DELAY HOURS buttons…
- SmartDispense water hardness calibration (models without 3-digit display, top controls)["Open the door and press any button to activate the lights.","Press Up arrow and DELAY HOURS…
- SmartDispense Water Hardness Calibration (Models Without a 3-Digit Display - Front Controls)["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
- SmartDispense Water Hardness Calibration (Models Without a 3-Digit Display - Top Controls)["Open the door and touch a pad to turn lights on.","Press the Up Arrow Pad and DELAY HOURS pad at…
- Toggle End-of-Cycle Audible Signal["Press the HEATED DRY pad 5 times within 3 seconds.","A triple beep will sound to indicate the…
- Toggle LOW DETERGENT LED (when not using SmartDispense)["Press the ADDED HEAT pad 5 times within 3 seconds.","You will hear 3 beeps; then the light will…
- Turbidity Sensor CalibrationMust be entered within 2 minutes of power up
- Water Hardness Calibration ModePDW8900
- Water Hardness Calibration Mode - Front Mount Control (PDW8900)["Dishwasher must be in standby mode
- Water Hardness Calibration Mode - Top Mount Control (PDW9700, PDW9900)["Dishwasher must be in standby mode.","Press up arrow to wake up control and illuminate the lights…
- Water Hardness Calibration Mode (PDW8900)Dishwasher in standby mode with door closed and latched
- Water Hardness Calibration Mode (PDW9700/PDW9900)Dishwasher in standby mode
Full entry steps, exit procedures, and test sequences are available in Max.
Related GE dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass