mypros+
Model reference

Hardwick PD-950

Range

13 documents80 error codes13 service modes

Available documentation

Tech Sheet

  • tech sheet w100652308 pg
    Covers this model
  • Tech Sheet - W11746523 - Rev A2 pg
    Covers this model
  • Tech Sheet - W11746529 - Rev A2 pg
    Covers this model
  • Tech Sheet - W11746531 - Rev A2 pg
    Covers this model
  • Tech Sheet - W11597687 - Rev A2 pg
    Covers this model
  • Kitchenaid Range KESS908SPS00 Tech Sheet 97627876 pg
    Covers this model
  • Tech Sheet - W115654522 pg
    Covers this model

Installation Guide

  • Installation Instructions72 pg
    Covers this model
  • Installation Instructions151 pg
    Covers this model
  • Installation Instructions112 pg
    Covers this model
  • Installation Instructions9 pg
    Covers this model
  • Installation Instructions9 pg
    Covers this model
  • Installation Instructions9 pg
    Covers this model
MyPros+ Max

Diagnose your Hardwick PD-950.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (80)

CodeMeaning
20Help code: Filling too quickly during cycle21Help code: Losing water during cycle (siphoning)d1Water level circuit failure on control board.d12Motor sensor circuit failure on control board.d13Blocked coin 2 or coin drop control circuit failure.d16Card reader communication failure (displayed when card reader is expected but…d4Lid switch circuit failure on control board.d5Blocked coin 1 or coin drop control circuit failure.d7Slow fill detected; fill time greater than 5 minutes.d8Slow drain detected; drain time greater than 2 minutes.d9Low voltage detected; less than 90 volts AC.F0Default F codeF0 E0No failure (default).F0-E0DefaultF1Electronic control malfunction.F1 E0Internal error (display board related).F1 E1Internal error (display board related).F1 E2Internal error (display board related).F1 E3Internal error (display board related).F1 E4Internal error (display board related).F1 E5Internal error (power board related).F1 E6Internal error (power board related).F1 E7Internal error (power board related).F1 E8Internal error (power board related).F1 E9Internal error (display board related).F1-E0Internal error.F1-E1Internal error.F1-E2Internal error.F1-E3Internal error.F1-E4Internal error.
View all 80 error codes
F1-E5CANCEL key drive line open.F1-E6CANCEL key drive line open.F1-E9Internal error.F1E0Internal board failure.F1E1A/D error(s).F1E2A/D error(s).F2 E0Stuck key (shorted key) on keypad.F2 E1Keypad disconnect or keypad disconnected.F2-E0Stuck key (short circuit) on keypad.F2-E1Keypad disconnected.F2E1Shorted keypad.F3 E0Main oven sensor open (top oven sensor opened).F3 E1Main oven sensor short (top oven sensor shorted).F3 E2Meat probe shorted.F3 E4Bottom oven sensor open (bottom/lower oven sensor open).F3 E5Lower/bottom oven sensor short (bottom oven sensor shorted).F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Main oven sensor open (upper oven sensor open circuit).F3-E1Main oven sensor shorted (upper oven sensor short circuit).F3-E2Meat probe shorted.F3-E3Oven temp too highF3-E4Bottom oven sensor open (lower oven sensor open circuit).F3-E5Bottom oven sensor shorted (lower oven sensor short circuit).F3-E6Warming drawer sensor open.F3-E7Warming drawer sensor shorted.F3E0Oven sensor opened, oven sensor shorted, bake/broil range over temperature, or…F4 E2Over temperature during cook mode.F4 E3Over temperature during clean mode.F4 E7Over temperature cavity 2 (temperature runaway error).F4-E2Over temperature during cook mode.F4-E3Over temperature during clean mode.F4-E7Over temperature in cavity 2.F5 E0Door latch mismatchF5 E1No operating latch / latch not operating.F5 E2Door switch fault.F5 E4Latch switch fault.F5 E7Unlock door errorF5-E0Door latch mismatchF5-E1Latch not operatingF5-E2Door switch fault.F5-E4Latch switch fault.F5-E7Unlock door errorF5E0Door and switches do not agree (Clean mode).F5E1Door latch not operating (Clean mode).F6 E4Lost communication between display board and power board.F6 E5Cancel key error.F6E1Oven over temperature when heating.F9E0Miswired house or miswired range.No displayControl not operational.

Service modes (13)

  • Bake Temperature Offset AdjustmentPress BAKE pad for 5 seconds
  • Cavity Size ProgrammingWithin 60 seconds of power up, press the following touchpads in sequence
  • diagnosticPress CANCEL > CANCEL > START within a 5-second period.
  • Diagnostic mode["Press Off to put the appliance in standby mode.","Press the following keys in sequence
  • Diagnostics modePress CANCEL > CANCEL > START within a 5 seconds period.
  • Diagnostics mode (error code recall)["Press the Off key to place the range in an idle state.","Press the Off and Start keys in the…
  • Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
  • Fault Code CheckPress and hold CANCEL key for 5 seconds.
  • Fault Code DisplayPress and hold CANCEL key for 5 seconds
  • Help ModeDepress Permanent Press keypad while in special pricing option Step 2.XX (or while 'dAS' displays…
  • Operator/Service Mode (Programming)Enter operator mode using the service switch (located behind service door).
  • Service Diagnostic ModePress CANCEL > CANCEL > START within a 5-second period.
  • Washer Diagnostic Cycle1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Hardwick range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass