mypros+
Model reference

Jenn-Air JJW6024HM0

Oven

7 documents32 error codes9 service modes

Available documentation

Tech Sheet

  • Wiring Sheet2 pg
    Covers this model
  • tech sheet w11686738 revA2 pg
    Covers this model

Service Manual

  • TECHNICAL MANUAL - JennAir® 60 cm Built-In Steam Oven28 pg
    Covers this model
  • Dimension Guide30 pg
    Covers this model

Tech Tip

  • Instruction Sheet1 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model
  • Trim Kit12 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air JJW6024HM0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (32)

CodeMeaning
CONFIGURATION_PARAMETERS_MYSMATCH_WITH_HWConfiguration parameters mismatch with hardware.F1E1Internal Oven Appliance Manager Error.F1E3ADC_DIAGF2E1ADC_DIAGF2E2Keypad/Display Disconnected.F2E4HMI Over Temperature.F2E5HMI Fault.F3E0Main oven sensor open or shorted.F3E3Oven meat probe open or shorted.F4E1Temperature ErrorF4E2Magnetron Temp Sensor Error.F4E4Humidity Sensor ErrorF4E7MWO Meat Probe/Temperature Probe connector or probe Failure.F5E0Latch errorF5E1Latch ErrorF5E2Door Switch MWO.F6E0User Interface/Appliance Manager communication error (detected via ESAM module).F6E1Over temperature (main/upper oven).F6E4User Interface/Appliance Manager state status mismatch.F6E6ADA Communication error (lost communication).F7E2Boiler NTC Out of Range outside the range -20°C to +145°C.F8E8This error appears if the drain pump is ON for maximum time and the water level…F9E0Product not wired correctly.FACTORY_TEST_NOT_PERFORMEDFactory test not performed.FCE1WiFi Module Connection.FCE2No link between WiFi module and wireless router.FCE3No link between WiFi module and internet.FCE4Antenna A not operational.FCE5Antenna B not operational.PEC_1_COOKINGSystem Failure
View all 32 error codes
PEC_1_IDLESystem FailurePEC_3_FAILSystem Failure

Service modes (9)

  • Component Activation["Enter Diagnostics Mode.","Touch or scroll to 'Component Activation' in the Diagnostics…
  • Diagnostics Mode["Press 'Setting', scroll down and press 'Info.'","Press 'Service and Support.'","Verify the model…
  • Error Diagnostic["Enter Diagnostics Mode.","Press 'Error Diagnostic' to see the last error detected."]
  • Error Diagnostics["Enter Diagnostics mode.","Press 'Error Diagnostics' to see the last error detected.","Clear the…
  • Sensors & Switches View["Enter Diagnostics Mode.","Navigate to Sensors & Switches section."]
  • Sensors and Switches (Status View)["Enter Diagnostics mode.","View current status of oven switches and sensor readings."]
  • Service Diagnostic Mode / Component Activation["1
  • System Info["Enter Diagnostics Mode.","Select 'System Info'."]
  • U.I. Configuration Mode["Press 'Setting', scroll down and press 'Info.' Press 'Service and Support.'","Check that the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass