mypros+
Model reference

Jenn-Air JMW2430WR02

Oven

11 documents37 error codes18 service modes

Available documentation

Service Manual

  • 27 & 30 Inch Microwave Combination Wall Ovens Job Aid60 pg
    Covers this model

Service Flash

  • Technical Service Pointer - JennAir Built-In Microwave Ovens and Single/Double and Combination Ovens19 pg
    Covers this model
  • JennAir Built In Microwave Ovens and Single Double and Combination Ovens F6 E6 F6 E8 and F6 F9 error code information not available on Tech Sheets19 pg
    Covers this model
  • Technical Service Pointer2 pg
    Covers this model
  • Technical Service Pointer - W10702370 (F8 E1)3 pg
    Covers this model
  • Technical Service Pointer W105627666 pg
    Covers this model

Tech Tip

  • Consumer Leave Behind - W10815485 - Rev A2 pg
    Covers this model
  • Instruction Sheet6 pg
    Covers this model
  • Instruction Sheet3 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model

Other

  • Service Pointer - 8178797 - Rev A (Microwave End of Cycle Operation)3 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air JMW2430WR02.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (37)

CodeMeaning
F0E0No error(s) foundF1E0Oven user interface (UI) failure.F1E1Internal Oven ACU (Appliance Control Unit) error.F1E2Internal failureF1E3Internal failureF1E4Microwave Oven Relay 4903 error.F1E5Microwave Oven Inverter error.F1E6Microwave Generation error.F2E0Keypad disconnected.F2E1Stuck/shorted key.F2E2Internal LED error.F3E0Main oven sensor open or shorted.F3E3Meat Probe Connector Jack or Meat Probe shorted.F4E1Microwave Cavity Temperature Sensor error.F4E2Magnetron Temperature Sensor error.F4E4Microwave Oven Humidity Sensor error.F4E5Weight sensor not within normal value.F4E6Microwave wave-guide heat sensor failure.F4E7Microwave probe failure.F4E8Inverter over temperature.F4E9Inverter and Magnetron over temperature.F5E0Door and latch switch do not agree.F5E1Latch not operating.F6E0Oven user interface lost communication.F6E1Over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperature (not for built-in ovens).F6E4User Interface / Appliance Manager state status mismatch.F6E5Cavity size is incorrect.F6E6Oven appliance manager lost communication.
View all 37 error codes
F6E8Lost communications with Microwave Oven Appliance Manager.F6EAUser interface over temperature (KitchenAid models only).F8E0Product not wired correctly (cooling fan related).F8E1Low fan speed overspeed.F8E2High fan speed underspeed.F8E3High fan speed overspeed.F9E0Product not wired correctly.

Service modes (18)

  • Cavity Size Select (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • Component ActivationFrom the Diagnostics Home Menu, press Up/Down navigation buttons to highlight Component Activation…
  • Component Activation (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Component Activation' in the Diagnostics menu and…
  • Diagnostic Mode1. Press LOWER OVEN > LOWER LIGHT > LOWER CANCEL (repeat two more times, total of 3 sequences). TIP
  • Diagnostic Mode (JennAir - touchscreen models)Press LOWER OVEN > LOWER LIGHT > OVEN CANCEL, repeat two more times (3 total sequences)
  • Diagnostic Mode (KitchenAid models)Press CANCEL > CANCEL > START
  • Diagnostics ModePress any 3 keys 3 times within 8 seconds.
  • Error DiagnosticFrom the Diagnostics Home Menu, press Up/Down navigation buttons to highlight Error Diagnostic…
  • Error Diagnostics (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Error Diagnostics' and touch 'OK'
  • Faults Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • Model Selection (JennAir models)Enter Diagnostics Mode
  • Model Selection (within Diagnostic Mode)["Plug in oven or connect power.","Enter Diagnostics Mode.","Touch or scroll to 'System…
  • Model Selection Procedure1
  • Relay Activation (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • Sensors and Switches (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Sensors and Switches' and touch 'OK'
  • Status Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • System InformationFrom the Diagnostics Home Menu, press Up/Down navigation buttons to highlight System Info, then…
  • System Information (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'System Information' and touch 'OK'

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass