mypros+
Model reference

Jenn-Air JMW3430WS03

Oven

5 documents37 error codes16 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10213741 - Rev B (FR)32 pg
    Covers this model
  • Tech Sheet - W10213732 - Rev B24 pg
    Covers this model

Service Manual

  • 27 & 30 Inch Microwave Combination Wall Ovens Job Aid60 pg
    Covers this model

Service Flash

  • Technical Service Pointer2 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air JMW3430WS03.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (37)

CodeMeaning
F0E0No error detectedF1E0Internal faultF1E1Internal faultF1E2Internal faultF1E3Internal failureF1E4Internal faultF1E5Internal faultF1E6Internal faultF2E0Keypad disconnected.F2E1Stuck/shorted key.F2E2LED error.F3E0Main oven sensor open or shorted.F3E3Meat probe sensor shorted.F4E1Microwave oven sensor faultF4E2Microwave oven sensor faultF4E4Microwave oven sensor faultF4E5Weight sensor not within normal value.F4E6Microwave wave-guide heat sensor failure.F4E7Microwave probe failure.F4E8Inverter over temperature.F4E9Inverter and Magnetron over temperature.F5E0Door switch and latch switch mismatch.F5E1Door latch not functioning.F6E0Loss of communication between user interface and appliance manager.F6E1Excessive oven temperature in Bake mode.F6E2Excessive oven temperature in Clean mode.F6E3Excessive temperature in warming drawer/mini oven (not applicable to built-in…F6E4User interface / appliance manager mismatch.F6E5Incorrect cavity size programmed.F6E6Oven appliance manager lost communication.
View all 37 error codes
F6E8Lost communications with Microwave Oven Appliance Manager.F6EAUser interface over temperature (KitchenAid models only).F8E0Fan low speed underspeedF8E1Fan low speed overspeedF8E2Fan high speed underspeedF8E3Fan high speed overspeedF9E0Product not wired correctly.

Service modes (16)

  • Cavity Size Select (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • Component Activation (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Component Activation' in the Diagnostics menu and…
  • diagnosticPress any one of the 3 keys 3 times within 8 seconds.
  • Diagnostic Mode1. Press LOWER OVEN > LOWER LIGHT > LOWER CANCEL (repeat two more times, total of 3 sequences). TIP
  • Diagnostic Mode (JennAir - touchscreen models)Press LOWER OVEN > LOWER LIGHT > OVEN CANCEL, repeat two more times (3 total sequences)
  • Diagnostic Mode (KitchenAid models)Press CANCEL > CANCEL > START
  • Diagnostics ModePress any three keys three times within 8 seconds.
  • Error Diagnostics (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Error Diagnostics' and touch 'OK'
  • Faults Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • Model Selection (JennAir models)Enter Diagnostics Mode
  • Model Selection (within Diagnostic Mode)["Plug in oven or connect power.","Enter Diagnostics Mode.","Touch or scroll to 'System…
  • Model Selection Procedure1
  • Relay Activation (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • Sensors and Switches (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Sensors and Switches' and touch 'OK'
  • Status Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • System Information (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'System Information' and touch 'OK'

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass