Model reference

Jenn-Air JGS1450ML0

Name: Jenn-Air JGS1450ML0
Brand: Jenn-Air

Range

7 documents37 error codes21 service modes

Available documentation

Service Manual

Dimension Guide10 pg
Covers this model
SERVICE MANUAL - Whirlpool®, Maytag®, KitchenAid®, Kenmore®, JennAir®, IKEA®, and Amana® Ranges104 pg
Covers this model

Tech Sheet

Tech Sheet - W11602648 - Rev A2 pg
Covers this model
Tech Sheet36 pg
Covers this model

Service Flash

Service Pointer - W11814535 - Rev A - Slide In Ranges - Flickering Oven Light3 pg
Covers this model

Tech Tip

Cleaning Kit Offer1 pg
Covers this model
Oven Cleaning Quick Reference Guide2 pg
Covers this model

MyPros+ Max

Diagnose your Jenn-Air JGS1450ML0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Jenn-Air Range

C-81 on my Jenn-Air JGS1450ML0

M+

Over temperature (induction cooktop)

From Tech Sheet W16049760, p.12:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (37)

CodeMeaning

C-81Over temperature (induction cooktop)C-82Over temperature (induction cooktop)C-83Temperature sensor stuck F-12Coil under current F-21Supply power frequency error F-25Stuck fan on Induction Power System (IPS) (Right or left side fan, depending on…F-36Temperature sensor is not working F-37Temperature sensor is not working F-40Induction Power System (IPS) failure F-42Power supply failure F-43Under voltage F-47Power supply from Induction Power Control (IPC) to User Interface is missing…F-56Wrong or invalid configuration F-58Wrong or invalid configuration (IPS)F-60UI does not work F1EEPROM communication error or internal control failure (Maxwell/MRC control).F1E0EEPROM Communication Error F1E1A/D error (LCC/LCX control).F1E2A/D error (LCC/LCX control).F2Keypad disconnected, stuck key, or cancel key error (Maxwell/MRC control).F2E0Keypad Disconnected F2E1Stuck Keypad F3E0Main Oven Sensor Open or Shorted F3E1Oven sensor shorted (LCC/LCX control).F3E2Drawer Sensor Open or Shorted F3E3Clean range over temperature (LCC/LCX control).F5E0Door and door position switch do not agree during Clean mode (Maxwell/MRC…F5E1Door latch not operating during Clean mode (LCC/LCX control).F5E2Door and door position switches do not agree during Clean mode (LCC/LCX…F6E0Oven User Interface lost communication between UI and ACU (Indigo control).

View all 37 error codes

F6E1Over Temperature F6E2Over temperature during clean mode (Maxwell/MRC control).F6E3Over temperature in warming drawer (Maxwell/MRC control).F6E4Oven User Interface UI and ACU state status mismatch (Indigo control).F8E0Cooling Fan Speed Too Low F8E2Cooling Fan Speed Too High F9E0Miswired

Service modes (21)

Auto Test - Maxwell/MRC Controls["Enter Diagnostics Mode (CANCEL>CANCEL>START)","Press the 'up' arrow, '+' key, or '3' key to…
Auto Test (Automatic Test Mode)Enter Diagnostics Mode (CANCEL>CANCEL>START within 5 seconds), then press the number 3 or 6 keypads…
Auto Test (Maxwell/MRC Controls)1
Clear Error CodesEnter diagnostic mode by pressing CANCEL>CANCEL>START within 5 seconds
Component Activation (Indigo Controls)From Diagnostics Menu, select Component Activation
Diagnostics ModePress CANCEL > CANCEL > START within 5 seconds.
Diagnostics Mode - Indigo Controls (Option 1)["Press HOME>FAVORITES>LIGHT (repeat this sequence three times in a row)","The warning will be…
Diagnostics Mode - Indigo Controls (Option 2)["Press TOOLS>INFO>SERVICE AND SUPPORT","Press the Diagnostics button for 1 minute","Press…
Diagnostics Mode - LCC/LCX Controls["Press CANCEL","Press CANCEL","Press START (all within a 5-second period)","Initial display shows…
Diagnostics Mode - Maxwell/MRC Controls["Press CANCEL","Press CANCEL","Press START (all within quick succession)","Display shows 'TEST ON'…
Diagnostics Mode (Indigo Controls) - Option 1Press HOME > FAVORITES > LIGHT, repeat three times in a row
Diagnostics Mode (Indigo Controls) - Option 2Press TOOLS > INFO > SERVICE AND SUPPORT
Diagnostics Mode (LCC/LCX Controls)Press CANCEL > CANCEL > START within a 5-second period. Scroll through settings with up arrow…
Diagnostics Mode (Maxwell/MRC Controls)Press CANCEL > CANCEL > START within 5 seconds
Diagnostics Test Mode Relay Checks (LCC/LCX Controls)While in Diagnostics Mode
Faults Viewing/ClearingEnter Diagnostics Mode (CANCEL>CANCEL>START within 5 seconds), then press the number 3 or 6 keypads…
Service Modes - Maxwell/MRC Controls (TEST ON, USAGE, ENG MODE, TEST MODE, VERSION, DISPLAY, FAULTS, EXTERNAL FAULTS, RELAY USAGE, AUTO TEST)["Press CANCEL>CANCEL>START to enter Service Mode","Use up arrow/+ key/3 key to scroll through…
Service Modes Menu (Maxwell/MRC Controls)Press CANCEL>CANCEL>START. Scroll through modes using up arrow/'+'/3 key
Temperature CalibrationPress the Settings or Options keypad until 'Temp Calib' is displayed
Test Mode (Manual Relay Activation)Enter Diagnostics Mode (CANCEL>CANCEL>START within 5 seconds), then press the number 3 or 6 keypads…
TEST ON - Relay Checks (Maxwell/MRC Controls)From Diagnostics Mode (CANCEL>CANCEL>START), at TEST ON display

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass