Model reference
KitchenAid KDTM704EBS0
Dishwasher
12 documents27 error codes8 service modes
Available documentation
Service Manual
- 2015 Microfiltration Dishwashers with Advanced ProDry™122 pg
- Dimension Guide2 pg
Tech Sheet
- Fiche technique W10758802C16 pg
- Tech Sheet - W10758801 Rev C12 pg
Service Flash
- KITCHENAID UNDER-COUNTER DISHWASHER - Intermittent Operation of the Capacitive Touch Control Panel Buttons3 pg
- Service Pointer - W11782244 - Rev A - Whirlpool, Maytag, KitchenAid, JennAir Dishwashers In-Line Fuse6 pg
- Technical Service Pointer - W10841713 (Door Clicking)6 pg
Tech Tip
- Instruction Sheet2 pg
- Instruction Sheet2 pg
Quick Reference
- Quick Reference Manual2 pg
Installation Guide
- Installation Instructions76 pg
Other
- Service Pointer - W11807380 - Rev A - Service Tool 2.0 Bluetooth Connection6 pg
MyPros+ Max
Diagnose your KitchenAid KDTM704EBS0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (27)
CodeMeaning
F10E1Dispenser electrical problemF10E3Drying fan errorF1E1Control detected K2 pilot relay stuck closed.F1E2Damaged or corrupted memory on control board, or incompatible software…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control due to loose user interface…F3E1Open connector or component in Temperature Sensing circuit, open or faulty…F3E2Shorted connection or component in Temperature Sensing circuit, shorted or…F3E3OWI failed calibration due to OWI failure or drain hose check valve not sealing.F4E3Wash motor not running due to loose connection in motor circuit and/or faulty…F5E1Door stuck openF5E2Door stuck closedF6E1Low or no water (mechanical problem)F6E2Fill valve electrical problemF6E3Suds or air in pumpF6E4Float switch openF6E7Disconnected or damaged flowmeter.F6E8Regen valve electrical problemF7E1No heatF7E2Heater stuck onF8E1Slow drainF8E2Drain motor electrical problemF8E3Drain motor stuck onF9E1Diverter can't find positionF9E2Diverter stuck onF9E3Diverter disk missingF9E4Lower spray arm errorService modes (8)
- Beeper Enable/DisablePress and hold Hi Temp button for 3 seconds
- Control LockPress and hold Control Lock button for 5 seconds to activate/deactivate.
- Customer Program Fast Advance ModeAfter starting a customer program, press HI TEMP
- Error Code ReadingPress any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second between key presses
- Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Service Diagnostic ProgramWith appliance idle, press any 3 keys in sequence 1-2-3-1-2-3-1-2-3 with maximum 1 second between…
- Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass