mypros+
Model reference

KitchenAid KOCE500EBS00

Microwave

7 documents52 error codes24 service modes

Available documentation

Tech Sheet

  • Tech Sheet - Wire Diagram W1104108124 pg
    Covers this model
  • Fiche technique24 pg
    Covers this model
  • Fiche technique W10756612 RevB24 pg
    Covers this model
  • Tech Sheet W10756611 RevB24 pg
    Covers this model

Service Manual

  • JennAir® and KitchenAid® 27" and 30" Microwave Combination Oven Technical Manual98 pg
    Covers this model

Service Flash

  • Service Pointer - W11493384 - Rev C - Built-in Microwave and Combo Wall Oven Microwave Door is Not Closing8 pg
    Covers this model

Tech Tip

  • installerlabel-w10643344-reva.pdf2 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KOCE500EBS00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (52)

CodeMeaning
F1 E0Oven user interface failure (internal).F1 E1Internal oven Appliance Manager error.F1 E4Microwave oven relay error.F1 E5Microwave oven inverter error.F1 E6Microwave generation error.F1E0Oven user interface (UI) failure.F1E1Internal Oven ACU (Appliance Control Unit) error.F1E4Microwave Oven Relay 4903 error.F1E5Microwave Oven Inverter error.F1E6Microwave Generation error.F2 E0Keypad disconnected.F2 E1Stuck/shorted keypad.F2E0Keypad disconnected.F2E1Stuck/shorted key.F3 E0Main oven sensor open or shorted.F3 E3Meat probe connector jack or meat probe shorted.F3E0Main oven sensor open or shorted.F3E1Meat probe connector jack or meat probe shorted.F3E3Meat Probe Connector Jack or Meat Probe shorted.F4 E1Microwave cavity temperature sensor error.F4 E2Magnetron temperature sensor error.F4 E4Microwave oven humidity sensor error.F4 E8Inverter over temperature.F4 E9Inverter and magnetron over temperature.F4E1Microwave Cavity Temperature Sensor error.F4E2Magnetron Temperature Sensor error.F4E4Microwave Oven Humidity Sensor error.F4E8Inverter over temperature.F4E9Inverter and Magnetron over temperature.F5 E0Door and latch switch do not agree.
View all 52 error codes
F5 E1Latch not operating.F5E0Door and latch switch do not agree.F5E1Latch not operating.F6Over-temperature at user interface.F6 E0Oven user interface lost communication / Oven appliance manager lost…F6 E1Over temperature.F6 E4User interface / Appliance manager state status mismatch.F6 E6Lost communication (contextF6 E8Lost communications with microwave oven appliance manager.F6 EAUser interface over temperature.F6E0Oven user interface lost communication.F6E1Over temperature.F6E4User Interface / Appliance Manager state status mismatch.F6E6Oven appliance manager lost communication.F6E8Lost communications with Microwave Oven Appliance Manager.F6EAUser interface over temperature (KitchenAid models only).F8E0Product not wired correctly (cooling fan related).F8E1Low fan speed overspeed.F8E2High fan speed underspeed.F8E3High fan speed overspeed.F9 E0Product not wired correctly.F9E0Product not wired correctly.

Service modes (24)

  • Cavity Size Select1
  • Cavity Size Select (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • cavity_size_select1
  • Component Activation (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Component Activation' in the Diagnostics menu and…
  • diagnostic1
  • Diagnostic Mode1. Press LOWER OVEN > LOWER LIGHT > LOWER CANCEL (repeat two more times, total of 3 sequences). TIP
  • Diagnostic Mode (JennAir - touchscreen models)Press LOWER OVEN > LOWER LIGHT > OVEN CANCEL, repeat two more times (3 total sequences)
  • Diagnostic Mode (KitchenAid models)Press CANCEL > CANCEL > START
  • Diagnostics ModePress CANCEL > CANCEL > START
  • Error Code Viewing and Clearing1
  • Error Diagnostics (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Error Diagnostics' and touch 'OK'
  • error_code_view1
  • Faults Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • Model Selection (JennAir models)Enter Diagnostics Mode
  • Model Selection (within Diagnostic Mode)["Plug in oven or connect power.","Enter Diagnostics Mode.","Touch or scroll to 'System…
  • Model Selection Procedure1
  • Relay Activation1
  • Relay Activation (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • relay_activation1. Enter diagnostic mode (CANCEL > CANCEL > START). 2. Press key 3 or 6 until the Relay Activation…
  • Sensors and Switches (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Sensors and Switches' and touch 'OK'
  • Status Screen1
  • Status Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
  • status_screen1
  • System Information (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'System Information' and touch 'OK'

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass