Model reference

KitchenAid KERC507EBL4

Name: KitchenAid KERC507EBL4
Brand: KitchenAid

Range

7 documents26 error codes17 service modes

Available documentation

Tech Sheet

Wiring Sheet - 97534811 pg
Covers this model
TECH SHEET4 pg
Covers this model

Service Manual

Kitchenaid Electronic Range Controls "B" & D Line Wall Ovens Job Aid93 pg
Covers this model

Training

Failure Codes & Wiring Diagrams for KitchenAid Freestanding & Slide-In Ranges And Built-In Ovens32 pg
Covers this model

Installation Guide

Instruction Sheet2 pg
Covers this model
Installation Instructions5 pg
Covers this model

Quick Reference

Quick Reference Manual2 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KERC507EBL4.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Range

F1 on my KitchenAid KERC507EBL4

M+

Control out of calibration.

From Tech Sheet W11509299, p.31:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (26)

CodeMeaning

F1Control out of calibration.F1-E0EEPROM read fault (silent fault, not displayed).F1-E1EEPROM checksum does not match at start key (silent fault, not displayed).F1-E3Configuration jumper change F1-E4Q8 shorted.F1-E9Stack overflow, highest priority fault.F2Keyboard shorted or CANCEL not operating.F2-E0Cancel key level too low (open).F2-E2Cancel key loop test failed.F2-E3Key held down too long or keyboard short.F2-E4Keys unsettled, probably due to noise.F3Oven probe shorted or open.F3-E0Platinum (PLAT) temperature sensor open.F3-E1Platinum (PLAT) temperature sensor shorted.F3-E2Oven temperature too high (runaway).F4Meat probe shorted.F4-E1Meat probe shorted (less than 1500 ohms).F5Door signal inconsistent.F5-E1Self-clean latch will not make after 30 seconds.F5-E3Loss of 120 VAC across L1 to ground, or Q19 circuit error (L1-N reverse).F5-E5Self-clean temperature not satisfied after 30 minutes.F5-E6Door locked with door open.F5-E7Door unlocked and will not unlatch.F6-E0Ambient sensor opened (too hot).F7-E0Input switches will not follow their strobe level (shorted to ground).PFPower failure

Service modes (17)

Bake Temperature Offset AdjustmentPush and hold the BAKE pad for four (4) seconds
Convection Freestanding/Slide-In Board ProgrammingAfter powering up the unit, press the following keypads in sequence
Hidden Functions - Calibration (Bake keypad)Touch and hold the Bake keypad for 5 seconds.
Hidden Functions - Clock Display Off (Clock keypad)Touch and hold the Clock keypad for 5 seconds.
Hidden Functions - Dehydrate (Conv. Bake keypad)Touch and hold the Conv
Hidden Functions - End-of-Cycle Tones Off (Cook Time keypad)Touch and hold the Cook Time keypad for 5 seconds.
Hidden Functions - Fahrenheit/Celsius Toggle (Broil keypad)Touch and hold the Broil keypad for 5 seconds.
Hidden Functions - Keypad Entry Tones Off (Stop Time keypad)Touch and hold the Stop Time keypad for 5 seconds.
Hidden Functions - Keypad Lockout (3 keypad)Touch and hold the #3 keypad for 5 seconds.
Hidden Functions - Last F/E Code and ROM Revision (0 keypad)Touch and hold the #0 keypad for 5 seconds.
Hidden Functions - Raising Bread (Baked Goods keypad)Touch and hold the Baked Goods keypad for 5 seconds.
Hidden Functions - Range Configuration Display (1 keypad)Touch and hold the #1 keypad for 5 seconds.
Hidden Functions - Sabbath Mode (6 keypad)Touch and hold the #6 keypad for 5 seconds (after oven has finished preheating in Bake mode).
Hidden Functions - Sell Mode (Timer Cancel keypad)Touch and hold the Timer Cancel keypad for 5 seconds.
Hidden Functions - Timer Operating Tones Off (Timer Start keypad)Touch and hold the Timer Start keypad for 5 seconds.
Hidden Functions - Tone Frequency Change (7 keypad)Touch and hold the #7 keypad for 5 seconds.
Non-Convection Freestanding/Slide-In Board ProgrammingAfter powering up the unit, press the following keypads in sequence

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass