mypros+
Model reference

KitchenAid KERC507HBL3

Range

3 documents27 error codes18 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 97822354 pg
    Covers this model

Service Manual

  • Kitchenaid Electronic Range Controls "B" & D Line Wall Ovens Job Aid93 pg
    Covers this model

Installation Guide

  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KERC507HBL3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (27)

CodeMeaning
F0Default F codeF1Electronic control malfunction.F1-E0EEPROM read fault (silent fault, not displayed).F1-E1EEPROM checksum does not match at start key (silent fault, not displayed).F1-E3Configuration jumper changeF1-E4Q8 shorted.F1-E9Stack overflow, highest priority fault.F2-E0Key held down too long, or key is shorted.F2-E1Keypad keytail not connected.F2-E2Cancel key loop test failed.F2-E3Key held down too long or keyboard short.F2-E4Keys unsettled, probably due to noise.F2-E5Cancel key drive line open.F3-E0Temperature sensor opened.F3-E1Temperature sensor shorted.F3-E2Oven temperature too high (over 301°C [575°F] in Cook mode).F3-E3Oven temperature too high (over 510°C [950°F] in Clean mode).F4-E1Meat probe malfunctionF5-E0Door is open, but latch is locked (condition exists when door switch is closed…F5-E1Self clean latch will not lock.F5-E3Loss of 120 VAC across L1 to ground, or Q19 circuit error (L1-N reverse).F5-E5Self clean temperature (288°C [550°F]) not reached within 45 minutes.F5-E6Door locked with door open.F5-E7Self clean latch will not unlock.F6-E0Ambient sensor opened (too hot).F7-E0Input switches will not follow their strobe level (shorted to ground).PFPower failure indication (not a failure of control).

Service modes (18)

  • Cancel Sabbath ModePress and hold key No
  • Convection Freestanding/Slide-In Board ProgrammingAfter powering up the unit, press the following keypads in sequence
  • Fault Code History RecallPress and hold key No
  • Hidden Functions - Calibration (Bake keypad)Touch and hold the Bake keypad for 5 seconds.
  • Hidden Functions - Clock Display Off (Clock keypad)Touch and hold the Clock keypad for 5 seconds.
  • Hidden Functions - Dehydrate (Conv. Bake keypad)Touch and hold the Conv
  • Hidden Functions - End-of-Cycle Tones Off (Cook Time keypad)Touch and hold the Cook Time keypad for 5 seconds.
  • Hidden Functions - Fahrenheit/Celsius Toggle (Broil keypad)Touch and hold the Broil keypad for 5 seconds.
  • Hidden Functions - Keypad Entry Tones Off (Stop Time keypad)Touch and hold the Stop Time keypad for 5 seconds.
  • Hidden Functions - Keypad Lockout (3 keypad)Touch and hold the #3 keypad for 5 seconds.
  • Hidden Functions - Last F/E Code and ROM Revision (0 keypad)Touch and hold the #0 keypad for 5 seconds.
  • Hidden Functions - Raising Bread (Baked Goods keypad)Touch and hold the Baked Goods keypad for 5 seconds.
  • Hidden Functions - Range Configuration Display (1 keypad)Touch and hold the #1 keypad for 5 seconds.
  • Hidden Functions - Sabbath Mode (6 keypad)Touch and hold the #6 keypad for 5 seconds (after oven has finished preheating in Bake mode).
  • Hidden Functions - Sell Mode (Timer Cancel keypad)Touch and hold the Timer Cancel keypad for 5 seconds.
  • Hidden Functions - Timer Operating Tones Off (Timer Start keypad)Touch and hold the Timer Start keypad for 5 seconds.
  • Hidden Functions - Tone Frequency Change (7 keypad)Touch and hold the #7 keypad for 5 seconds.
  • Non-Convection Freestanding/Slide-In Board ProgrammingAfter powering up the unit, press the following keypads in sequence

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass