mypros+
Model reference

Magic Chef 16TW-3BK

Range

7 documents40 error codes12 service modes

Available documentation

Tech Sheet

  • Instruction Sheet - 9753053 - Rev A8 pg
    Covers this model
  • techsheet 445655610 pg
    Covers this model
  • Tech Sheet – do not Discard10 pg
    Covers this model
  • TECH SHEET – KDRP467KSS05 KA Range10 pg
    Covers this model
  • Tech Sheet - 4454079 - Rev B4 pg
    Covers this model

Service Manual

  • Self-Cleaning Slide-In Gas Ranges Job Aid68 pg
    Covers this model

Other

  • 432250068 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef 16TW-3BK.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (40)

CodeMeaning
:Power failure indicationF0Default F codeF0 E0No error(s) found.F01Temperature sensor opened (open circuit in oven temperature sensor).F02Welded element relays (element relay contacts stuck closed).F03EEPROM error in the electronic control.F05Door or latch problems (mechanical or electrical failure in door latch…F06Electronic control malfunction.F1Electronic control malfunction.F1 E0EEPROM communications error.F1 E1EEPROM checksum failure.F1 E2UL A/D error(s).F1 EOEEPROM communications failure.F1-E0Key held down too long or key is shorted.F1-E1Keypad keytail not connected.F1-E2UL A/D error(s).F1-E5CANCEL key drive line open.F1-E6CANCEL key drive line open.F2Touch panel failure.F2 E0Shorted key / Stuck key.F2 E1Keytail unplugged from control board.F2 EOShorted key on keypad.F2-E0Temperature sensor opened (R=2875 ohm by spec).F2-E1Temperature sensor shorted (R=825 ohm by spec).F3 E0Oven temperature sensor circuit is open.F3 E1Oven temperature sensor is shorted.F3 E2Bake range over temperature condition.F3 E3Clean range over temperature condition.F3-E0Oven temperature sensor open circuit.F3-E1Oven temperature sensor shorted.
View all 40 error codes
F3-E2Oven temp too highF3-E3Oven temp too highF5 E0Door switch and latch switch do not agree.F5 E1Door lock solenoid not operating or latch switch failure.F5 E2Latch during CLEAN error.F5-E0Door is open but latch is locked (door switch is open indicating open door, and…F5-E1Self-clean latch will not lock/unlock.F5-E2Latch during CLEAN error.F6MW relay (Relay 4903) failure.PFPower failure has occurred.

Service modes (12)

  • Bake Temperature Offset AdjustmentPress BAKE pad for 5 seconds
  • Cavity Size ProgrammingWithin 60 seconds of power up, press the following touchpads in sequence
  • Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
  • Fault Code CheckPress and hold CANCEL key for 5 seconds.
  • Fault Code DisplayPress and hold CANCEL key for 5 seconds
  • Last error code recallPress and hold CANCEL/OFF key for 5 seconds until last error code is displayed.
  • Oven Temperature CalibrationPress and hold the BAKE keypad for 5 seconds. The current offset will be shown in the 3-digit…
  • Self-Diagnostic / Touch Panel and PCBA Test["Press and hold the STOP/CLEAR button while opening the door.","While still holding the STOP/CLEAR…
  • Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds
  • Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds. Current offset (if any) is shown in 3-digit display. CAL is…
  • Test mode (diagnostic)Within 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
  • Test mode readoutAfter entering test mode, press the arrow down key to cycle through

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax