Model reference
Magic Chef 31FN-2X-EC
Range
46 error codes11 service modes
MyPros+ Max
Diagnose your Magic Chef 31FN-2X-EC.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (46)
CodeMeaning
d13The Coin 2 sensor is detected as blocked; coin vault may be full of money, or…d16Gen 2 Debit Card Reader Errord5The Coin 1 sensor is detected as blocked; coin vault may be full of money, or…d9Low voltageF01Indicates a main control fault.F03Main control detects an out of range pressure signal from the pressure…F07Main control cannot determine position of shifter (shifter system failure).F1 E1Main control faultF1 E6Low voltage detectedF11Motor control faultF2 E1Washer keypad stuck errorF20Long fillF21Long drainF22Lid lock faultF24Inlet water temperature faultF25Basket speed sensor faultF26Lid switch faultF27Overflow conditionF29Lid unlock faultF3 E2Pressure sensor faultF3 E3Inlet water temperature faultF32No fillF5 E1Lid switch faultF5 E3Lid switch faultF5 E4Lid unlock faultF6 E1Communication failure between CCU and UIF7 E1Basket speed sensor faultF7 E2Motor control faultF7 E5Shifter faultF70Communication failure between CCU and UIView all 46 error codes
F71Communication failure between CCU and UIF73The User Interface EEPROM identification does not match the expected value in…F74The User Interface EEPROM identification does not match the expected value in…F77Off balance load detected.F8 E1No fillF8 E3Overflow conditionF9 E1Long drainFC E1Model/serial not programmedFC E2Model/serial do not matchFC E4USB faultFC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication failure.
Service modes (11)
- Help Mode["Enter Service Mode.","Use the NORMAL keypad to advance to program location 2.xx (Special Pricing…
- P-01 Clear Errors["Enter Service Diagnostic Test Modes.","Display shows P-01.","Press START to clear active error…
- P-02 Cycle Credit["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-02.","Press START to provide…
- P-03 Service Diagnostic["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-03.","Press START to initiate…
- P-04 Manual Diagnostic["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-04.","Press START to initiate…
- P-05 Calibration Cycle["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-05.","Press START to initiate…
- P-07 UI Diagnostics["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-07.","Press START to start UI…
- P-09 Tachometer Verification["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-09.","Press START to start…
- P-12 Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-12.","Press START to start…
- Service Diagnostic Test Modes (entry)["For coin (PD) models
- Technician Service Access Code (free vend models only)["This method is only available on washers set to free vend (6 00).","Press the LEFT UPPER, RIGHT…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Magic Chef range models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass