mypros+
Model reference

Magic Chef 31FN-7-NR

Range

4 documents49 error codes21 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10509194 - Rev A (CVTY-FR)8 pg
    Covers this model
  • Wiring Diagram2 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 818477712 pg
    Covers this model

Installation Guide

  • Installation Instructions4 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef 31FN-7-NR.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (49)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…1-3Control detected stuck key(s) in keypad or keypad connection.10-1Dispenser electrical problem10-2Vent wax motor electrical problem.10-3Drying fan error2-1User interface stuck key or short circuit(s) in keypad or in control's input…2-2Software or hardware incompatibility problem with control.3-1Open temperature sensing circuit3-2Shorted temperature sensing circuit3-3OWI/thermistor sensor failed calibration.4-3Wash motor not running5-1Door stuck open5-2Door stuck closed6-1Inlet water6-2Inlet water6-3Inlet water6-4Inlet water6-6Inlet water6-7Disconnected or damaged flowmeter.6-8Inlet water7-1Heating7-2Heating8-1Draining8-2Draining8-3Draining9-1Diverter9-2Diverter stuck on9-3Diverter disk missing from sump.F1-E0EEPROM communication error in oven control module.
View all 49 error codes
F1-E0 (cooktop)EEPROM communication error on cooktop control module (EGO).F1-E5Sensor out of range in oven control module.F1-E7Circuit board thermistor open or short-circuited in oven control module.F1-E7 (cooktop)Cooktop board sensor/thermistor open or short-circuited.F1-E9WIDE queue full in oven control module.F1-E9 (cooktop)WIDE queue full on cooktop control module.F2-E0Keypad disconnected from oven control module.F2-E1Stuck key on oven control keypad.F2-E1 (cooktop)Stuck key on cooktop control module.F2-E2Cancel key error on oven control module.F3-E0Main oven temperature sensor open or short-circuited.F3-E2Warming drawer temperature sensor open or short-circuited (on some models).F5-E0Door and door switch mismatchF6-E0 (cooktop)Right side cooktop communication error.F6-E1Bake over-temperature condition.F6-E3Warming drawer over-temperature condition.F6-E4 (cooktop)Left side cooktop communication error.F6-E5 (cooktop)Oven control module communication error (from cooktop perspective).F9-E0Incorrect home or range wiring connection (L1-L2-N wiring).

Service modes (21)

  • Cooktop EGO Control Module Diagnostic Mode1
  • Error History ReadingEnter Service Diagnostics Cycle. Error codes are displayed in intervals 24 (Error 1
  • MRC2 Oven Control Auto Test1
  • MRC2 Oven Control Diagnostic ModePress CANCEL > CANCEL > START
  • MRC2 Troubleshooting Mode - AUTO TESTEnter diagnostic mode, scroll to mode 10 'AUTO TEST'.
  • MRC2 Troubleshooting Mode - CONTROL RESETEnter diagnostic mode, scroll to mode 6 'CONTROL RESET'.
  • MRC2 Troubleshooting Mode - DISPLAYEnter diagnostic mode, scroll to mode 5 'DISPLAY'.
  • MRC2 Troubleshooting Mode - ENG MODEEnter diagnostic mode, scroll to mode 2 'ENG MODE'
  • MRC2 Troubleshooting Mode - EXTERNAL FAULTSEnter diagnostic mode, scroll to mode 8 'EXTERNAL FAULTS'.
  • MRC2 Troubleshooting Mode - FAULTSEnter diagnostic mode, scroll to mode 7 'FAULTS'
  • MRC2 Troubleshooting Mode - RELAY USAGEEnter diagnostic mode, scroll to mode 9 'RELAY USAGE'.
  • MRC2 Troubleshooting Mode - TEST MODE (Relay Control)Enter diagnostic mode, scroll to mode 3 'TEST MODE'
  • MRC2 Troubleshooting Mode - TEST ON (Relay Control)Press CANCEL > CANCEL > START
  • MRC2 Troubleshooting Mode - USAGEEnter diagnostic mode (CANCEL > CANCEL > START), then scroll to mode 1 'USAGE'.
  • MRC2 Troubleshooting Mode - VERSIONEnter diagnostic mode, scroll to mode 4 'VERSION'.
  • Rapid Advance Mode (Cycle Operation)After starting a cycle, press HI TEMP
  • Rapid Advance Mode (during active cycle)Press HI TEMP
  • Rapid Advance Mode (in-cycle)After starting a cycle, press HI TEMP
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Service Diagnostics Error History ReadoutAfter entering Service Diagnostics Cycle, errors are displayed in intervals 24 (Error 1
  • Temperature Calibration Adjustment1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass