mypros+
Model reference

Magic Chef 31FN-7X

Range

1 document56 error codes15 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11639164 - Rev A2 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef 31FN-7X.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (56)

CodeMeaning
drnDrain pump system problemF0E2Oversuds condition detectedF0E3Overload conditionF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F1E1ACU1 (Appliance Control Unit 1) fault.F1E2Motor control section of the main control has faulted.F1E3Mismatch of ACU and UIF2E1Stuck or shorted key on the keypad.F2E2Keypad/Display disconnected from the control.F2E3UI mismatchF2E4UI software errorF2E5HMI 1 (Human Machine Interface 1) fault.F3E0Main oven temperature sensor fault.F3E1Pressure system faultF3E2Inlet water temperature faultF3E3Convertible Compartment Temperature Sensor failure.F3E4Freezer Compartment or Main Evaporator In Sensor failure.F3E5Freezer Compartment Evaporator Out Sensor failure.F3E6Refrigeration Compartment Evaporator In Sensor failure.F4E1Heater stuck onF4E2Heater not turning onF4E3Convertible Compartment Evaporator Heater failure.F5E0Main door and latch switches do not agree (mismatch between door switch and…F5E1Main door latch motor fault.F5E2Lid lock will not lock or lid lock failure.F5E3Lid lock will not unlock.F5E4Lid not opened between cyclesF6E1Communication failure between ACU1 and HMI1.F6E2Communication error
View all 56 error codes
F6E3Communication errorF7E0Loss of powerF7E1Loss of power during spinF7E2Motor drive module failureF7E3Basket engaged during washF7E4Basket re-engagement failureF7E5Cooling fan error.F7E6Cooling fan blocked.F7E7Motor unable to meet target RPM.F7E8Motor over temperatureF7E9Locked rotorF8E1Long fillF8E3Overflow or flood conditionF8E6Water hazardF9E0Power cord miswired.F9E1Drain pump system problemF9E2Drain pump system problemFAE1Refrigeration Compartment or Main Evaporator Fan failure.FAEBDamper 1 (RC Damper) failure.FBE1Main cavity over temperature condition.FCE1Model/Serial number not programmed into control.FCE2Model/Serial number do not match between components.FCE3Wi-Fi radio fault.FEE6Main cavity bake element fault.FEE7Main cavity broil element fault.LFLong fill

Service modes (15)

  • Error Code Display ModePress and Hold Refrigerator Temperature button + Cubed Ice buttons for 5 seconds.
  • Fault Code Display / Clearing["Enter Service Diagnostic Mode.","If saved fault code exists, it will be flashing in the display…
  • Fault ResetFrom Service Test Mode, press 1st button for 5 seconds to reset the faults.
  • Key Activation & Encoder Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • Manual Control ModeFrom Service Test Mode, press the selected first button for a short duration to enter manual…
  • Service Calibration["Enter Service Test Mode.","Select function number 052 using Soil Level/Temp buttons or cycle…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostics - Option A["Press Settings.","Navigate to Diagnostics home.","Select Service Diagnostics Code.","Enter code…
  • Service Diagnostics - Option B["Press Settings.","Navigate to Diagnostics home.","Select Service Diagnostics Code.","Enter any 3…
  • Service Diagnostics (Automated Test Cycle)["Enter Service Test Mode.","Select function number 051 using Soil Level/Temp buttons or cycle…
  • Service Test ModePress and release any 3 keypad buttons, three times consecutively (1,2,3; 1,2,3; 1,2,3)
  • Service Test Mode (Load Control)["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Show Fault ModeFrom Service Test Mode, press 1st button for a short duration.
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • Software Version Display ModeFrom Service Test Mode, press 1st button for 3 seconds.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass