mypros+
Model reference

Magic Chef 31HN-10K

Range

3 documents50 error codes25 service modes

Available documentation

Service Manual

  • 30″ Freestanding Self-Cleaning Electric Range72 pg
    Covers this model
  • Job Aid - 8178042 (KR-31)72 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 39800578 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef 31HN-10K.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (50)

CodeMeaning
:Power failure indication00No faults present.1Dryer thermistor short sensed2Thermistor open sensed3Door circuit failure4Possible motor transistor error6Non-volatile memory error8Stuck keyCdCondenser Fan Output fault.CLCommunication Link Lost between boards.CPCompressor Output fault.Delay LED + Heated Dry LEDMemory / Software failure detected during Field Service Test.Delay LED + Heavy Wash LEDThermistor failure detected during Field Service Test.Delay LED + Hi Temp Wash LEDTurbidity Sensor failure detected during Field Service Test.Delay LED + Light Wash LEDMotor low current fault detected during Field Service Test.Delay LED + Normal Wash LEDMotor high current fault detected during Field Service Test.dHDefrost Heater Output fault.dPDamper Motor Output fault.E1Thermistor is open (open circuit detected in thermistor).E2Thermistor has shorted (short circuit detected in thermistor).E3User interface keyswitch or software mismatch between console panel/touchpad…EFEvaporator Fan Output fault.EOOpen thermistor detected.ESShorted thermistor detected.F0 E0Factory defaultF1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.
View all 50 error codes
F2Touch panel failure.F2 E0Shorted key.F2 E1Key tail unplugged.F2E1Touch panel failure.F3 E0Oven sensor openedF3 E1Oven sensor shortedF3 E2Bake range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor openedF3 E5Oven sensor shortedF3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3HHumidity sensor failureF4E4Humidity sensor error.F5 E0Door switches do not agree.F5 E1Door latch not operating.F6MW relay (Relay 4903) failure.F8 E0N/A.F8E5Exhaust air temperature detection failure.PFPower failure occurred while the dryer was running.

Service modes (25)

  • Accessing Diagnostic Codes (13 Key Membrane)["Press Air Fluff and Time (^) to enter Service Mode.","Press the Wrinkle Release key to access the…
  • Accessing Diagnostic Codes (15 Key Membrane)["Press Air Fluff and Time (+) to enter Service Mode.","Press the Wrinkle Release key to access the…
  • Clearing Diagnostic Codes["While in diagnostic mode, press Air Fluff and Wrinkle Release keys simultaneously for 3 seconds…
  • Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","Press Cancel button to enter Standby mode (colon ':'…
  • Diagnostic Test Mode["Unit must be in Standby (unit plugged in, display off).","Alternately press the Less Time (∨) and…
  • Field Service TestPress the Heated Dry key 6 times followed by the Start key within 8 seconds.
  • Force/Terminate DefrostToggle freezer door light switch 5 times within 6 seconds.
  • Manual Function TestPress the Heated Dry key 5 times followed by the Start key within 8 seconds
  • Membrane Pad Check["Enter System Check Mode first.","Press Air Fluff and Sensor Dry keys simultaneously for 2 seconds…
  • Self-Diagnostic / Touch Panel and PCBA Test["Press and hold the STOP/CLEAR button while opening the door.","While still holding the STOP/CLEAR…
  • Self-Diagnostic Test Mode["Press and hold CANCEL/OFF while opening the door.","While still holding the CANCEL/OFF button…
  • Service Mode["Press Air Fluff and Time (^) keys simultaneously for 3 seconds (13 Key Membrane) OR press Air…
  • Service Mode (Mode A – System Checks and Mode B – Calibration)1
  • Service Mode A - Option 1: Display Error CodesWhile in Service Mode A, press the Confirm Settings Key to enter this option.
  • Service Mode A - Option 10: Display Door Opening CountWhile in Service Mode A, navigate to Option 10 and press the Confirm Settings Key.
  • Service Mode A - Option 11: Display Defrost Terminator StatusWhile in Service Mode A, navigate to Option 11 and press the Confirm Settings Key.
  • Service Mode A - Option 2: Display Average On and Off TimesWhile in Service Mode A, navigate to Option 2 and press the Confirm Settings Key.
  • Service Mode A - Option 3: Forced Pull-downWhile in Service Mode A, navigate to Option 3 and press the Confirm Settings Key.
  • Service Mode A - Option 4: Independent Evaporator Fan ModeWhile in Service Mode A, navigate to Option 4 and press the Confirm Settings Key.
  • Service Mode A - Option 5: Display Current Actual TemperaturesWhile in Service Mode A, navigate to Option 5 and press the Confirm Settings Key.
  • Service Mode A - Option 6: Force Compressor On OnlyWhile in Service Mode A, navigate to Option 6 and press the Confirm Settings Key.
  • Service Mode A - Option 7: Force Condenser Fan On OnlyWhile in Service Mode A, navigate to Option 7 and press the Confirm Settings Key.
  • Service Mode A - Option 8: Force Evaporator Fan On OnlyWhile in Service Mode A, navigate to Option 8 and press the Confirm Settings Key.
  • Service Mode A - Option 9: Force Motorized Damper On OnlyWhile in Service Mode A, navigate to Option 9 and press the Confirm Settings Key.
  • System Check Mode["Enter Service Mode first.","Press Air Fluff and Signal (+) keys simultaneously for 3 seconds (13…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass