Model reference
Magic Chef BT16KS-4S
Range
1 document69 error codes25 service modes
Available documentation
Tech Sheet
- Tech Sheet - 97822354 pg
MyPros+ Max
Diagnose your Magic Chef BT16KS-4S.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (69)
CodeMeaning
C1Blocked coin 1 or coin drop control circuit failure (coin recognition and price…C2Blocked coin 2 or coin drop control circuit failure (coin recognition and price…d1Blocked coin 1 or coin drop UI control circuit failure (coin recognition and…d10Overheating of motord11MCU errord12Tachometer errord13Coin 2 errord14Pump disconnectedd15Load detected in washer during Washer Cleanout Cycle.d16Generation 2 debit card reader errord17Door lock errord19Door unlock errord2Voltage detected below 90 VAC for 8 seconds.d20Communication failure between CCU and MCU.d21Overflow conditiond23Communication failure between CCU and UI.d24Temperature sensor errord3UI failured4Door switch errord5Coin 1 errord6CCU errord7No water detected entering washer.d8Long draind9Low voltage detection errorEdNot receiving communications from installed debit card reader in Enhanced…F0Default F codeF01CCU errorF1Electronic control malfunction.F11MCU errorF2Exhaust thermistor open, temperature drops below 18°F (>50 kΩ) for 1 minute in…View all 69 error codes
F2-E0Key held down too long, or key is shorted.F2-E1Keypad keytail not connected.F2-E5Cancel key drive line open.F20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.F29Door unlock errorF3Exhaust thermistor shorted, temperature above 250°F (<500Ω) for 1 minute in Run…F3-E0Temperature sensor opened.F3-E1Temperature sensor shorted.F3-E2Oven temperature too high (over 301°C [575°F] in Cook mode).F3-E3Oven temperature too high (over 510°C [950°F] in Clean mode).F31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F4UI is not receiving communications from CCU (cycles and price display disabled…F4-E1Meat probe malfunctionF5CCU is not receiving communications from UI (cycles and price display disabled…F5-E0Door is open, but latch is locked (condition exists when door switch is closed…F5-E1Self clean latch will not lock.F5-E5Self clean temperature (288°C [550°F]) not reached within 45 minutes.F5-E7Self clean latch will not unlock.F6UI Microprocessor is not able to read or verify EEPROM (cycles and price…F7UI EEPROM memory is a CRC failure (cycles and price display disabled until…F70Communication failure between CCU and User Interface (UI).F73UI failureF74Coin 1 errorLdWasher lid sense error on control board or due to power line interference…LFWater level detection error on control board or due to power line interference…LSMotor sense error detected on control board or due to power line interference.LVVoltage detected below 90 VAC for 8 seconds.SdLast drain occurring during final spin was slow.SFLast fill was slow.tFWater temperature sense error when equipped with temperature sensing water…
Service modes (25)
- Cancel Sabbath ModePress and hold key No
- Code Display Mode["PD Models
- Cycle Credit["Enter Flashing Mode (entire display flashing).","Press the PERM
- diagnostic["Enter set-up mode first.","Navigate to set-up code 6 xx or 7 xx, or have a diagnostic code…
- diagnostic mode["Enter set-up mode first.","While in any of the set-up codes 1 through 6, anytime a diagnostic…
- Fault Code History RecallPress and hold key No
- field diagnostic cycle["Enter diagnostic mode (entire display flashing).","Press the LOWER MIDDLE key pad to start the…
- Flashing Mode["PD Models
- help["Enter set-up mode.","Navigate to special pricing option code 2.XX.","Press COTTON/WHITES button…
- help mode["Enter set-up mode first.","Navigate to special pricing option mode (code 2.XX).","Press the LOWER…
- Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
- Help Mode (PD Models)["Open the service door.","Press the DELICATES AND KNITS button until the display reads…
- Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the WHITES button."]
- Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the DELICATES AND KNITS button."]
- Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the COLORS button."]
- Service Access Code["Only functions on washers set up for 0 vend price without any Special Pricing, and Coin/Debit…
- Service Access Code Entry["Only functions on washers set up for 0 vend price without any Special Pricing set-up, and…
- set-up["Insert service access door key, turn, and lift to remove service access door.","If a card reader…
- set-up mode["PD Models
- Set-Up Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door.","Use the lower…
- Set-Up Mode (PR Models via AA1)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
- Set-Up Mode (PR Models)["Once debit card reader is installed, insert a set-up card (supplied by reader manufacturer) into…
- Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the BRIGHTS button."]
- Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (enter set-up mode).","Press and hold the QUICK CYCLE button…
- Washer Diagnostic Mode (Flashing Mode)["First enter 'Start Operating Set-Up' (set-up mode).","Press and hold the QUICK CYCLE button for 1…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Magic Chef range models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass