mypros+
Model reference

Maytag DM15H-14B

Microwave

3 documents39 error codes9 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11646012 - Rev A2 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 85244282 pg
    Covers this model
  • Instruction Sheet - 82690932 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag DM15H-14B.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (39)

CodeMeaning
F0E1Load detected in drum during Clean Washer cycle.F0E2Excessive suds detected in washer; washer is running a suds reduction routine.F0E4High temperature error during wash cycle.F0E5Off balance load detected.F1E1Main relay open or shorted.F1E2MCU over- or under-voltage error.F1E4MW Relay Error 0F2E1Keypad stick errorF2E2User Interface Software Error 1F2E3User Interface Software Error 2F3E1Pressure sensor signal missing or out of range.F3E2Wash NTC (thermistor) open or shorted.F3E3Inlet thermistor is open; temperature drops below 18°F (> 245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (< 328 ohms).F3E5Dry NTC fault; dry temperature sensor is out of range, open circuit, or short…F3E6Accelerometer error.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F3E8IR sensor failureF4E1Wash heater relay error or no feedback signal; ACU cannot detect temperature…F4E2Wash heater relay error.F4E3Hood NTC failureF4E4Low L2 voltage (less than 30V) detected at the CCU.F4E9MW relay synchro Error 1F5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6E1No communication from the HMI detected by ACU.F6E2No communication from the ACU detected by the HMI.F6E3No communication from the MCU detected by the ACU.F7E10Motor disconnected error.
View all 39 error codes
F7E12MC/MCU overload.F7E2MC/MCU over temperature error or over current error/internal failure.F7E8MC/Motor over temperature error.F7E9Motor will not turn (locked rotor).F7EAMotor disconnected error (alternate display of F7E10).F7ECMC/MCU overload (alternate display of F7E12).F8E1Water inlet valve failure.F8E3Overflow condition.F9E1Long drain time.

Service modes (9)

  • Diagnostics Mode["Press Settings
  • Fault Code DisplayFrom Service Diagnostic Mode
  • Fault/Error Code Display["Activate Service Diagnostic Mode; the most recent fault code is shown immediately upon…
  • Human-Machine Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Quick Diagnostic Test["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 30 seconds after…
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • UI Component TestFrom Service Diagnostics, navigate to Component Activation > UI Component Test

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag microwave models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax