Model reference

Maytag MEW7627DE02

Oven

7 documents47 error codes13 service modes

Available documentation

Tech Sheet

Tech Sheet W1040887416 pg
Covers this model
Tech Sheet32 pg
Covers this model
TechSheet W10796081 RevB56 pg
Covers this model
Tech Sheet56 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model
installerlabel-w10643344-reva.pdf2 pg
Covers this model

Installation Guide

Installation Instructions32 pg
Covers this model

MyPros+ Max

Diagnose your Maytag MEW7627DE02.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Oven

C-81 on my Maytag MEW7627DE02

M+

Over temperature — Type 2 failure, not

From Tech Sheet W11250527, p.19:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (47)

CodeMeaning

C-81Over temperature C-82Over temperature F-12Coil under current F-21Supply power frequency is incorrect F-25Stuck fan on power control board (right or left side fan, depending on which…F-36Temperature sensor is not working F-37Temperature sensor is not working F-40Power control board failure F-42Power supply failure F-47Power supply from power control board to User Interface is missing, or WIDE…F-56Wrong or invalid configuration F-58Wrong or invalid configuration F-60UI (User Interface) does not work F-61Power control board does not work F1 E0Internal error on MRC board.F1 E1Internal error on MRC board.F1 E7Internal error on MRC board.F1 E9Internal error on MRC board.F1E0EEPROM Communication Error F1E1Upper RTD Uncalibrated F1E2Lower RTD Uncalibrated F1E5Sensor Usage Out of Range F1E7PCB Thermistor Open or Shorted F1E9WIDE Queue Full F2 E0Keypad disconnected from MRC board.F2 E1Stuck key detected on keypad.F2 E2Invalid keypad detected.F2 E3Cancel key error on keypad.F2E0Keypad Disconnected F2E1Stuck Keypad

View all 47 error codes

F2E2Cancel or Off Keypad Error F3 E0Main oven sensor open or shorted (upper cavity on single or double oven).F3 E1Main oven sensor open or shorted (lower cavity on double oven).F3E0Main Sensor Open or Shorted (Upper)F3E1Main Sensor Open or Shorted (Lower)F4E1Microwave Oven Magnetron Thermistor Open or Shorted F4E4Microwave Oven Humidity Sensor Open or Shorted F5 E0Door and latch switches do not agree.F5 E1Latch not operating.F5E0Door and Latch Switches Do Not Agree F5E1Latch Not Operating F6 E1Over temperature during cooking.F6 E2Over temperature during cleaning.F6E0Lost Communication with Microwave F6E1Over Temp Cook F6E2Over Temp Clean F9E0Miswired

Service modes (13)

Auto Test Mode1
Diagnostics ModePress CANCEL>CANCEL>START or OFF>OFF>ON within 5 seconds. Use TEMP/TIME '+' or '-' or 'More' or…
Fault Display Reset1
Faults ScreenEnter Diagnostics Mode, navigate to 'Faults' using TEMP/TIME '+'/'-' or 'More'/'Less' or number 3/6…
Manual Configuration Mode["This menu is accessible only during the first minutes after the cooktop is plugged in.","Step 1
Semi Automatic Test ModeEnter Diagnostics Mode, then navigate with TEMP/TIME '+'/'-' or 'More'/'Less' or number 3/6 keypads…
Software Version1
Temperature CalibrationPress Settings or Options keypad until 'Temp Calib' is displayed
Temperature Calibration (Double Oven)1
Temperature Calibration (Single Oven)1
Test ModeEnter Diagnostics Mode, then navigate with TEMP/TIME '+'/'-' or 'More'/'Less' or number 3/6 keypads…
Test Mode (Relay Activation)1
Usage Codes1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass