mypros+
Model reference

Maytag MEW9530FZ03

Oven

5 documents32 error codes9 service modes

Available documentation

Tech Sheet

  • Wiring Diagram - W10796020 - Rev A2 pg
    Covers this model
  • Tech Sheet W1040887416 pg
    Covers this model

Service Manual

  • KitchenAid Job Aid W10807512 - 27 & 30" Built-In Single and Double Wall Ovens52 pg
    Covers this model

Wiring Diagram

  • Wiring Sheet - W11326948 - Rev A2 pg
    Covers this model

Installation Guide

  • Installation Instructions32 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MEW9530FZ03.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (32)

CodeMeaning
C-81Over temperatureC-82Over temperatureF-12Coil under currentF-21Supply power frequency is incorrectF-25Stuck fan on power control board (right or left side fan, depending on which…F-36Temperature sensor is not workingF-37Temperature sensor is not workingF-40Power control board failureF-42Power supply failureF-47Power supply from power control board to User Interface is missing, or WIDE…F-56Wrong or invalid configurationF-58Wrong or invalid configurationF-60UI (User Interface) does not workF-61Power control board does not workF1 E0User Interface failureF1 E1Appliance Manager failure.F2 E0Keypad disconnected from User Interface.F2 E1Stuck or shorted key on keypad.F3 E0Main/upper oven temperature sensor open or shorted.F3 E1Bottom/lower oven temperature sensor open or shorted.F3 E3Meat Probe connector jack or Meat Probe shorted.F5 E0Door and latch input switches do not agree (main/upper oven).F5 E1Latch not operating (main/upper oven).F5 E3Door and latch input switches do not agree (lower oven).F5 E4Latch not operating (lower oven).F6 E0Oven User Interface lost communication.F6 E1Over temperature condition (main/upper oven).F6 E3Over temperature condition (lower oven).F6 E4Appliance Manager failure.F6 E6Oven Appliance Manager lost communication (main/upper oven).
View all 32 error codes
F6 E9Oven Appliance Manager lost communication (lower oven).F6 EAUser Interface over temperature condition.

Service modes (9)

  • Cavity Size SelectEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • cavity_size_selectPress CANCEL > CANCEL > START to enter Diagnostic Mode
  • diagnosticPress CANCEL, then CANCEL, then START.
  • Diagnostic ModePress CANCEL, then CANCEL, then START.
  • Error Code Review and ClearEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • error_code_review_and_clearEnter Diagnostic Mode (CANCEL > CANCEL > START), then press keypad 3 or 6 to scroll to the error…
  • Manual Configuration Mode["This menu is accessible only during the first minutes after the cooktop is plugged in.","Step 1
  • Relay ActivationEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • relay_activationEnter Diagnostic Mode (CANCEL > CANCEL > START), then press keypad 3 or 6 to scroll to the RELAY…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass