Model reference

Maytag MEW9630DS02

Oven

7 documents39 error codes14 service modes

Available documentation

Tech Sheet

Tech Sheet - W10507056 - Rev B32 pg
Covers this model
Tech Sheet W1040887416 pg
Covers this model
Tech Sheet32 pg
Covers this model

Service Flash

Technical Service Pointer9 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model
installerlabel-w10643344-reva.pdf2 pg
Covers this model

Installation Guide

Installation Instructions32 pg
Covers this model

MyPros+ Max

Diagnose your Maytag MEW9630DS02.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Oven

C-81 on my Maytag MEW9630DS02

M+

Over temperature — Type 2 failure, not

From Tech Sheet W15548101, p.33:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (39)

CodeMeaning

C-81Over temperature C-82Over temperature F-12Coil under current F-21Supply power frequency is incorrect F-25Stuck fan on power control board (right or left side fan, depending on which…F-36Temperature sensor is not working F-37Temperature sensor is not working F-40Power control board failure F-42Power supply failure F-47Power supply from power control board to User Interface is missing, or WIDE…F-56Wrong or invalid configuration F-58Wrong or invalid configuration F-60UI (User Interface) does not work F-61Power control board does not work F1 E0Oven appliance manager failure.F1 E1Oven user interface failure.F1 E7Internal error on MRC board.F1 E9Internal error on MRC board.F2 E0Keypad disconnected.F2 E1Stuck/shorted key.F2 E2Invalid keypad detected.F2 E3Keypad hardware failure.F3 E0Main oven sensor open or shorted.F3 E1Bottom oven sensor open or shorted.F5 E0Single/double upper oven door and latch switch do not agree.F5 E1Single/double upper oven latch not operating.F5 E3Double lower oven door and latch switch do not agree.F5 E4Double lower oven door latch not operating.F5 E5Upper door switch reads constant high.F5 E6Lower door switch reads constant high.

View all 39 error codes

F6 E0Oven user interface lost communication.F6 E1Single/double upper oven F6 E2Single/double upper oven F6 E3Double lower oven F6 E4Oven user interface/appliance manager state mismatch.F6 E5No cavity size command.F6 E6Oven appliance manager F6 E7Lost communication with MWO appliance manager.F6 EBDouble lower oven

Service modes (14)

Auto Test1
Auto Test Mode1
Diagnostics ModePress CANCEL > CANCEL > START.
Error Codes1
Fault Display Reset1
Manual Configuration Mode["This menu is accessible only during the first minutes after the cooktop is plugged in.","Step 1
Model Select1
Relay Activation1. Enter Diagnostics Mode (CANCEL > CANCEL > START). 2. Press the quickset pad below Relay…
Software Version1
Status Screen1
Temperature Calibration (Double Oven)1
Temperature Calibration (Single Oven)1
Test Mode (Relay Activation)1
Usage Codes1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass