mypros+
Model reference

Maytag MGT8655XS00

Range

6 documents30 error codes15 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10311748 - Rev A16 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Service Flash

  • Technical Service Pointer - W10418467 (Gas Smell)3 pg
    Covers this model

Other

  • DP W10367616 LP instruct final2 pg
    Covers this model

Installation Guide

  • Installation Instructions40 pg
    Covers this model
  • Instruction Sheet1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MGT8655XS00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (30)

CodeMeaning
E0 F1EEPROM communication error.E0 F2Keypad disconnected.E0 F3Main oven temperature sensor open or shorted (upper oven).E0 F5Door and latch switches do not agree (Clean mode).E0 F6Lost communications.E0 F9Product is mis-wired.E1 F1Upper RTD uncalibrated.E1 F2Stuck key.E1 F3Main oven temperature sensor open or shorted (lower oven).E1 F5Door latch not operating (Clean mode).E1 F6Over temperature during cook mode (runaway temp).E2 F1Lower RTD uncalibrated.E2 F2Stuck key.E2 F6Over temperature during clean mode (runaway temp).E3 F6Over temperature in warming drawer (runaway temp).E5 F1Sensor usage out of range.E7 F1PCB thermistor/sensor open or shorted.E9 F1WIDE Queue full.F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F2Shorted/stuck key detected on the control keypad.F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F6 E*Control communication failure.F9House miswired

Service modes (15)

  • Control ResetEnter Diagnostics Mode first (CANCEL > CANCEL > START)
  • Diagnostics ModePress CANCEL > CANCEL > START within 5 seconds
  • Display TestEnter Diagnostics Mode first (CANCEL > CANCEL > START)
  • Faults (view recorded faults)Enter Diagnostics Mode first (CANCEL > CANCEL > START)
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Semi Automatic TestEnter Diagnostics Mode first (CANCEL > CANCEL > START)
  • Temperature CalibrationPress SETTINGS/OPTIONS until 'Temp Calib' is highlighted, then follow instructions to see the…
  • Test Mode (manual relay activation)Enter Diagnostics Mode first (CANCEL > CANCEL > START)
  • UsageEnter Diagnostics Mode first (CANCEL > CANCEL > START)
  • VersionEnter Diagnostics Mode first (CANCEL > CANCEL > START)

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass