Model reference

Maytag MGT8800FZ00

Range

12 documents32 error codes6 service modes

Available documentation

Tech Sheet

Tech Sheet W11333113B2 pg
Covers this model
Tech Sheet W11333113 RevA2 pg
Covers this model
Wiring Diagram - W10784962 - Rev A2 pg
Covers this model
Tech Sheet W11565449 RevA2 pg
Covers this model
MGT8800FZ tech sheet64 pg
Covers this model

Bulletin

DIP - W107149136 pg
Covers this model

Tech Tip

Control Guide20 pg
Covers this model
Instruction Sheet2 pg
Covers this model

Installation Guide

Installation Instructions40 pg
Covers this model
Installation Instructions36 pg
Covers this model
Installation Instructions40 pg
Covers this model
Instruction Sheet1 pg
Covers this model

MyPros+ Max

Diagnose your Maytag MGT8800FZ00.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Range

C-81 on my Maytag MGT8800FZ00

M+

Over temperature.

From Tech Sheet W12253128, p.20:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (32)

CodeMeaning

C-81Over temperature.C-82Over temperature.C-83Temperature sensor stuck.F-12Induction cooktop coil under current (Type 1 failure, affects only one burner).F-21Induction cooktop supply power frequency error (Type 2 failure, affects all…F-25Stuck fan on Induction Power System (IPS)F-36Induction cooktop temperature sensor is not working (Type 1 failure).F-37Induction cooktop temperature sensor is not working (Type 1 failure).F-40Stuck fan on Induction Power System (IPS)F-42Temperature sensor is not working.F-43Under voltage.F-47Power supply from Induction Power Control (IPC) to User Interface is missing…F-56Wrong or invalid configuration.F-58Wrong or invalid configuration.F-60User Interface does not work.F1E0EEPROM communication error.F1E1Upper RTD Uncalibrated F1E2Lower RTD Uncalibrated F1E5Sensor Usage Out of Range F1E7PCB Thermistor Open or Shorted F1E9WIDE queue full.F2E0Keypad disconnected.F2E1Stuck keypad.F2E2Cancel or Off key error / Warming Zone Off keypad error.F3E0Main sensor open or shorted (upper oven).F3E1Main sensor open or shorted (lower oven).F5E0Door and latch switches do not agree.F5E1Latch not operating.F6E0Lost WIDE communication.F6E1Over temperature during cook cycle.

View all 32 error codes

F6E2Over temperature during clean cycle.F9E0Miswired / incorrect wiring.

Service modes (6)

Clear All Error CodesEnter Diagnostics mode (CANCEL > CANCEL > START or OFF > OFF > ON within 5 seconds)
Cooktop Controls Diagnostic ModePress any 3 different keypads in sequence, then repeat the same 3-key sequence 2 more times within…
Oven Diagnostics ModePress CANCEL > CANCEL > START (or OFF > OFF > ON) within 5 seconds.
Semi Automatic Test ModeEnter Diagnostics Mode, navigate to 'Semi Auto Test' using TEMP/TIME +/- or More/Less or 3/6…
Temperature CalibrationPress Settings or Options keypad until 'Temp Calib' is displayed
Test Mode (Relay Activation)Enter Diagnostics Mode (CANCEL>CANCEL>START or OFF>OFF>ON within 5 seconds). Navigate to 'Test…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass