mypros+
Model reference

Maytag MGT8885XB00

Range

7 documents26 error codes19 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10311752 - Rev A32 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Service Flash

  • Technical Service Pointer - W10418467 (Gas Smell)3 pg
    Covers this model

Tech Tip

  • Instruction Sheet4 pg
    Covers this model

Other

  • DP W10367616 LP instruct final2 pg
    Covers this model

Installation Guide

  • Installation Instructions40 pg
    Covers this model
  • Instruction Sheet1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MGT8885XB00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (26)

CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1 E0EEPROM communication error.F1 E1Upper RTD uncalibrated (internal error).F1 E2Lower RTD uncalibrated (internal error).F1 E5Sensor usage out of range (internal error).F1 E7PCB thermistor/sensor open or shorted.F1 E9WIDE queue full.F2Shorted/stuck key detected on the control keypad.F2 E0Keypad disconnected.F2 E1Stuck key detected.F2 E2Stuck key detected.F3Oven sensor opened or oven sensor shorted.F3 E0Main oven sensor open or shorted (upper oven).F3 E1Main oven sensor open or shorted (lower oven).F3 E2Warming drawer temperature sensor fault.F5 E0Door and latch switches do not agree during Clean mode.F5 E1Door latch not operating during Clean mode.F5 E2Door switch fault.F6 E*Control communication failure.F6 E0Lost communications.F6 E1Over temperature during cook mode (runaway temp).F6 E2Over temperature during clean mode (runaway temp).F6 E3Over temperature in warming drawer (runaway temp).F9House miswiredF9 E0Product is mis-wired.

Service modes (19)

  • Control ResetAfter entering Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads…
  • Diagnostics ModePress CANCEL > CANCEL > START within 5 seconds.
  • Display TestAfter entering Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads…
  • Faults (Error Code Review)1
  • Faults DisplayAfter entering Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads…
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Semi Automatic TestAfter entering Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads…
  • Semi Automatic Test Mode1
  • Temperature CalibrationPress SETTINGS/OPTIONS until 'Temp Calib' is highlighted, then follow the instructions to see the…
  • Test Mode (Manual Relay Activation)After entering Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads…
  • Usage CheckAfter entering Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads…
  • Usage Mode1
  • Version CheckAfter entering Diagnostics Mode, press TEMP/TIME '+' or '-' keypads (or Number 3 or 6 keypads…
  • Version Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass