mypros+
Model reference

Maytag YMER8800FW6

Range

9 documents26 error codes19 service modes

Available documentation

Service Manual

  • EnerGuide1 pg
    Covers this model
  • Tech Manual - W11401670 - Rev A16 pg
    Covers this model
  • SERVICE MANUAL - Whirlpool®, Maytag®, KitchenAid®, Kenmore®, JennAir®, IKEA®, and Amana® Ranges104 pg
    Covers this model

Tech Sheet

  • Tech Manual16 pg
    Covers this model
  • Fiche technique - Tech Sheet W10667176 Rev A8 pg
    Covers this model
  • Tech Sheet - W10667169 - Rev C8 pg
    Covers this model

Bulletin

  • Installation Pointer - W11663212 - Rev B - New Terminal Block for Tulsa FSR6 pg
    Covers this model

Tech Tip

  • Cleaning Kit Offer1 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag YMER8800FW6.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (26)

CodeMeaning
F1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7Circuit board thermistor open or short-circuited.F1E0EEPROM communication error.F1E5Sensor out of range.F1E7Board thermistor open or shorted.F1E9WIDE File queue full.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F2E0Keypad disconnected.F2E1Stuck key detected.F2E2Cancel key error.F3-E0Oven temperature sensor open or short-circuited (measured at P10-1 and P10-2).F3-E2Oven temperature sensor issue (measured at P10-3 and P10-4, warm drawer sensor).F3E0Main oven sensor open or shorted.F3E2Warming drawer sensor open or shorted.F5-E0Door switch/latch fault (measured at P7-5 and P7-4).F5E0Door and switches do not agree (Clean modeF6-E1Excessive temperature fault.F6-E2Excessive temperature fault.F6-E3Excessive temperature fault.F6E1Over temperature during cook mode.F6E2Over temperature during clean mode.F6E3Over temperature in warming drawer.F9E0Mis-wired house or range.

Service modes (19)

  • Auto TestFrom service mode (CANCEL > CANCEL > START), press up arrow / '+' / '3' to scroll to 'AUTO TEST'…
  • CONTROL RESETFrom service mode, scroll to step 6 'CONTROL RESET'.
  • Diagnostics Mode (Auto Test)1
  • Diagnostics Mode (MRC Control)Press CANCEL > CANCEL > START
  • Diagnostics Mode (Service Mode Entry)Press CANCEL > CANCEL > START
  • DISPLAYFrom service mode, scroll to step 5 'DISPLAY'.
  • ENG MODEPress CANCEL > CANCEL > START to enter Service Mode
  • ENG MODE (Engineering Mode)From service mode, scroll to step 2 'ENG MODE'
  • FAULTSFrom service mode, scroll to step 7 'FAULTS'.
  • MRC Control Module Diagnostics / Service ModePress CANCEL > CANCEL > START to enter service mode
  • RELAY USAGEFrom service mode, scroll to step 8 'RELAY USAGE'.
  • Service Diagnostic Mode / Auto Test["Press CANCEL > CANCEL > START to enter the diagnostic mode.","Press the up arrow, '+' (plus…
  • Temperature Adjustment1
  • Temperature Offset AdjustmentPress OVEN LIGHT for 5 seconds
  • TEST MODEFrom service mode, scroll to step 3 'TEST MODE'.
  • TEST ON - Relay ControlEnter service mode (CANCEL > CANCEL > START)
  • TEST ON (Relay Checks)Press CANCEL > CANCEL > START. Upon entry, 'TEST ON' is displayed. Use specific key presses to…
  • USAGEFrom service mode, scroll to step 1 'USAGE'.
  • VERSIONFrom service mode, scroll to step 4 'VERSION'.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass