Model reference

Midea US-FC70-DS12DSH/C0401E

Name: Midea US-FC70-DS12DSH/C0401E
Brand: Midea

Washer

1 document30 error codes10 service modes

Available documentation

Service Manual

Laundry Washer and dryer combo Service Manual48 pg
Covers this model

MyPros+ Max

Diagnose your Midea US-FC70-DS12DSH/C0401E.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Midea Washer

E10 on my Midea US-FC70-DS12DSH/C0401E

M+

Water level doesn't change within 7

From Service Manual 601891, p.23:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (30)

CodeMeaning

E10Water level doesn't change within 7 minutes with valves open (no water inlet or…E11Too much water left in the unit at standby or end of cycle (non-drain…E12Water level in drum exceeds a certain level for alarm (water fill overflow).E20Main PCB cannot get pump signal; unit closes valves and stops motor.E21Water level doesn't change within 3 minutes with pump started (drain timeout).E30Door cannot be locked after more than 3 failed attempts.E31Door cannot be unlocked after more than 3 failed attempts.E33Main PCB cannot get water level switch signal.E34Temperature sensor on water heater is open circuit.E35Temperature sensor on water heater is short circuit.E36Water heater doesn't work.E37Drum drying outlet temperature sensor failed; drying function cannot work.E38Drum drying inlet temperature sensor failed; drying function cannot work.E3ADrying heater open circuit; drying function cannot work.E40EEPROM failed; memory chip of the PCB is broken.E50/E52Inverter PCB overload; unit cannot work.E50/E53Inverter module temperature failure; unit cannot work.E50/E55Motor speed signal lost; unit will stop operation.E50/E56Motor temperature over-protection; unit will stop operation.E50/E57Inverter module temperature failure; unit will stop operation.E50/E58Inverter module failure; unit will stop operation.E50/E5AConnection failure between inverter module and main control PCB; unit will stop…E50/E5BInverter module failure; unit will stop operation.E50/E5COver voltage on inverter module; unit will stop operation.E50/E5DLow voltage on inverter module; unit will stop operation.E50/E5EInverter module failure; unit will stop operation.E64Signal between main PCB and inverter PCB is abnormal; unit will stop operation.E70Button blocked/stuck; unit cannot work.E80Main PCB cannot get signal from display PCB; unit cannot work.E81Main PCB cannot get signal from display PCB; unit cannot work.

Service modes (10)

t02 - Error Code Review1
t04 - Display Test1
t05 - Pump Test1
t06 - Water Switch Test1
t07 - Water Heater Test1
t08 - Drying Heater Test1
t09 - Wash Function Test1. Enter test mode. 2. Navigate to 't09' display. 3. Press Start/Pause to activate. Display shows…
t10 - Spin Function Test1
t12 - Water Inlet Valve Test1. Enter test mode. 2. Navigate to 't12' display. 3. Press Start/Pause
Test Mode (Diagnostic)1. Shut down the machine by pressing the On/Off button. 2. Disconnect the plug from the power…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Midea washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass