mypros+
Error code reference

Midea Washer Error Code E10

Water level doesn't change within 7 minutes with valves open (no water inlet or water inlet overtime).

Midea codesMidea washer codes

Water level doesn't change within 7 minutes with valves open (no water inlet or water inlet overtime).

First step from the service manual

Check if water faucet is turned on and that the screens on the hoses are not restricted.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E10.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E10 means on a Midea washer

The E10 error code on a Midea washer indicates that the water level sensor has not detected any change in water level within a 7-minute window after the inlet valves have been commanded to open. This is a timed fill fault, meaning the control board opened the water inlet valve or valves, waited the maximum allowable fill duration, and received no confirmation from the pressure switch or water level sensor that water entered the drum. The fault protects the machine from running a wash cycle dry or running indefinitely while waiting for fill conditions that will never be met.

The water inlet system on these washers consists of the supply hoses, inlet screens, the solenoid-operated inlet valve assembly, and the water level pressure switch and its associated air hose. A failure or restriction at any point in this chain can trigger E10. The most common starting point for diagnosis is the water supply itself: a closed or partially closed faucet, kinked hoses, or clogged inlet screens can restrict flow to the point where the drum never reaches a detectable level. These are the simplest possible causes and should always be ruled out before moving to internal components.

If the supply and screens are clear, the fault can originate from a failed inlet valve solenoid that is not opening electrically, a pinched or disconnected pressure switch air hose that prevents the sensor from reading water level changes, or a defective water level pressure switch itself. In less common cases, a control board that is not sending the correct signal to the inlet valve can also produce this fault. Systematic diagnosis working from the water supply inward will identify the failed component.

Source: manufacturer service documentation.

Common causes of E10

  1. 01

    Closed or restricted water supply

    Wiring / connection

    The water faucets behind the washer may be fully or partially closed, or the supply hoses may be kinked, preventing adequate water flow into the machine. Check that both faucets are turned fully counterclockwise and that the hoses are not bent or pinched.

  2. 02

    Clogged inlet hose screens

    Wiring / connection

    Small mesh screens inside the hose connections at the back of the washer catch debris and sediment from the water supply. When these screens become restricted, water flow drops below the rate needed to raise the drum level within the 7-minute window. Remove the hoses and inspect the screens, cleaning or replacing them if they appear blocked.

  3. 03

    Faulty water inlet valve

    Part replacement

    The solenoid-operated inlet valve may have failed electrically or mechanically, preventing it from opening even when the control board sends the open command. If the supply and screens are clear but no water enters, the valve assembly should be tested for proper solenoid continuity and replaced if defective.

  4. 04

    Defective or disconnected pressure switch or air hose

    Part replacement

    The water level pressure switch detects fill progress through a small rubber air hose connected to the tub. If this hose is pinched, cracked, or disconnected, the switch cannot detect rising water and the control board never receives confirmation that fill is occurring, triggering E10 even if water is flowing. Inspect the hose for damage and verify it is firmly seated at both ends.

  5. 05

    Control board failure

    Part replacement

    If the control board is not sending the correct voltage signal to the inlet valve solenoid, the valve will not open regardless of supply conditions. This is a less common cause and should be considered only after the supply, screens, valve, and pressure switch have been ruled out.

See the test procedure for each cause

Frequently asked questions about E10

What does E10 mean on a Midea washer?
E10 means the washer did not detect any change in water level within 7 minutes after the water inlet valves were opened. The machine monitors fill progress through a water level pressure switch, and if no fill is detected in that window, it stops the cycle and displays E10. This protects the washer from running a wash cycle without water. The fault can be caused by a closed water supply, clogged inlet screens, a failed inlet valve, or a problem with the pressure switch.
How do I fix an E10 error on my Midea washer?
Start by confirming that both hot and cold water supply faucets behind the washer are fully open and that the hoses are not kinked. Next, turn off the water, disconnect the hoses from the back of the washer, and inspect the small mesh screens in the hose fittings for debris, cleaning them if necessary. If the supply and screens are clear, the next steps involve checking the water inlet valve and the pressure switch air hose for faults. If you are not comfortable working with internal components, a qualified technician can complete this diagnosis safely.
Is it safe to keep using my washer when E10 is displayed?
No, you should not attempt to run a wash cycle while E10 is active. The error means the drum is not filling with water, so running a cycle could cause the motor and other components to operate under conditions they are not designed for. Resolve the fill fault before resuming use. The washer has halted operation automatically as a protective measure.
Will resetting my Midea washer clear the E10 error?
Unplugging the washer for a minute and restarting it may temporarily clear the displayed code, but E10 will return immediately on the next cycle if the underlying cause has not been fixed. A reset does not repair a closed faucet, clogged screen, or failed valve. Address the root cause of the fill fault first, then restart the washer to confirm the error does not come back.
How much does it cost to repair an E10 error on a Midea washer?
The cost depends on the cause. Cleaning clogged inlet screens costs nothing beyond a few minutes of time. Replacing a water inlet valve typically runs in the range of $25 to $75 for the part, with additional labor if a technician performs the repair. A water level pressure switch is generally in the $15 to $50 range for parts. If the control board is at fault, replacement costs can be considerably higher, often $100 to $300 or more for parts alone, which may affect the decision to repair versus replace an older unit.

Related Midea washer codes

All Midea washer codes
View all 39 Midea washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass