Model reference

Miele G4286VI

Name: Miele G4286VI
Brand: Miele

Dishwasher

1 document22 error codes4 service modes

Available documentation

Service Manual

Descriptive Technical Documentation141 pg
Covers this model

MyPros+ Max

Diagnose your Miele G4286VI.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Miele Dishwasher

F01 on my Miele G4286VI

M+

Water/Heating NTC temperature sensor

From Service Manual 573754, p.46:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (22)

CodeMeaning

F01Water/Heating NTC temperature sensor short-circuited; heating will not be…F02Water/Heating NTC temperature sensor open-circuited; heating will not be…F11Drainage fault; water is present in the appliance and is not being drained off.F12Water intake fault at start of step; during the first 5 seconds of any water…F13Water intake fault at end of step; desired number of flow meter pulses not…F14Water intake fault F18Flow meter stationary state monitor B3/4; water inlet valve is open when it…F19Flow meter B3/4 stiff and not turning freely; test routine to monitor free…F24Heater relay contact fault; supply voltage detected at electronic inputs when…F25Desired temperature fault; during heating stage the desired temperature was not…F26Boiling protection; temperature at NTC temperature sensor has exceeded 90°C…F40Electronic fault; a hardware fault that cannot be repaired by the service…F42Line frequency registration fault; power frequency cannot be clearly…F51Heater pressure switch fault; 1 second after program start, heater relay K1/1…F52Heater pressure switch has reset during heating; program continues without…F63Slide shutter fault; even though slide shutter motor has been activated, there…F69Circulation pump blocked; with the circulation pump operating, the heater…F70Float switch fault; overflow float switch has activated indicating water in the…F84Slide shutter positioning fault; an attempt to position the slide shutter has…F85Slide shutter signal change fault; even though the slide shutter has not been…F86Salt container lid contact fault; reed switch is constantly open during the…F88Turbidity sensor fault; false or no values from turbidity sensor; program…

Service modes (4)

Service Mode (G 42xx, G 44xx)["Open the door.","Switch off the machine.","Press and hold the Program button.","Switch on the…
Service Mode (G 43xx, G 527x, G 528x, G 537x, G 538x, G 519x, G 547x, G 548x)["Open the door.","Switch off the machine.","Press and hold the Program button.","Switch on the…
Service Programming Mode (G 42xx, G 44xx)["Open the door.","Switch off the machine.","Press and hold the Program button.","Switch on the…
Service Programming Mode (G 43xx, G 527x, G 528x, G 537x, G 538x, G 519x, G 547x, G 548x)["Open the door.","Switch off the machine.","Press and hold the Program button.","Switch on the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Miele dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass