Model reference
Viking VDSC530
Oven
13 documents29 error codes3 service modes
Available documentation
Service Manual
- Service Manual - 30 Inch Dual Fuel Range39 pg
- VDSC530 30 Inch Dual Fuel Range Service Manual39 pg
- Diagnostic Quick Sheet -VDSC530-536 and 548 T series5 pg
- Service Manual - 30, 36, & 48 Inch Dual Fuel Range53 pg
- Service Manual 30, 36, & 48 Inch Dual Fuel Range53 pg
- Service Manual Range SMC 0003B VDSC530 536 548 5 Series Dual Fuel53 pg
Bulletin
- Technical Bulletin - Sealed burners can be placed onto burner bases improperly causing ignition issues1 pg
- Technical Bulletin - Redesigned Seal Burner System1 pg
Service Flash
- Instruction Sheet ISC-0036A for TC-0082A-SP13 pg
Tech Tip
- Adjusting oven temperature offsets35 pg
Job Aid
- Window Pack Insulation Repair6 pg
Other
- Diagnostic Quick Sheet VDSC530 536 and 548 T series5 pg
- VDSC530 Range30 pg
MyPros+ Max
Diagnose your Viking VDSC530.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (29)
CodeMeaning
1 flash every 4 secNormal operation (idle and active states) on DSI board.2 flashesRTD (Griddle Probe) fault2 flashes every 4 secDSI control fault.3 flashes every 4 secIgnition lockout4 flashes every 4 secGas solenoid fault on DSI board.5 flashes every 4 secDSI control fault.6 flashes every 4 secGas solenoid fault on DSI board.7 flashes every 4 secPower up with channel on8 flashes every 4 secGas solenoid fault on DSI board.Cooling FanCooling fan error indicated by 3 flashes on the Cycle Light and the Clean Light…DSI 1 FlashNormal operation (idle and active states)DSI 2 FlashesDSI control faultDSI 3 FlashesIgnition lockoutDSI 4 FlashesGas solenoid faultDSI 5 FlashesDSI control faultDSI 6 FlashesGas solenoid faultDSI 7 FlashesPower up with channel onDSI 8 FlashesGas solenoid faultDSI LED ContinuousDSI control faultDSI No LEDNo power to the DSI moduleHigh LimitHigh limit error indicated by 4 flashes on the Cycle Light and the Clean Light…LatchDoor latch error indicated by the Cycle Light OFF and the Clean Light flashing…LED on continuouslyDSI control fault.ModelModel identification error indicated by the Cycle Light flashing 1 second ON, 1…No LEDNo power to the DSI module.RTDOven probe (RTD sensor) error indicated by the Cycle Light flashing 1 second…RTD (Griddle)Griddle RTD probe faultRTD (Oven Probe)Oven RTD probe faultRTD (Oven)Oven RTD probe faultService modes (3)
- Diagnostics and Testing1. Enter Settings mode (hold CLEAR/SETTINGS for 3 seconds). 2. Toggle selector knob to reach the '-
- Oven Offset CalibrationFrom any of the Settings parameters, press and hold simultaneously the OVEN TEMP and CLEAR/SETTINGS…
- SettingsPush and hold CLEAR/SETTINGS button for 3 seconds to access Settings.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Viking oven models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass