Model reference
Whirlpool MDPS6124RZ0
Dishwasher
11 documents50 error codes8 service modes
Available documentation
Service Manual
- Dimension Guide12 pg
- SERVICE MANUAL - Maytag Dishwashers 4-Blade Stainless Steel Chopper76 pg
Tech Sheet
- tech sheet w11366142 revb2 pg
- Tech Sheet - W113661422 pg
- Technical Service Sheet W11366142C2 pg
Service Flash
- Service Pointer - W11782244 - Rev A - Whirlpool, Maytag, KitchenAid, JennAir Dishwashers In-Line Fuse6 pg
- Technical Service Pointer - W11723599 - Rev A - Spray Arm Falls Off2 pg
- Technical Service Pointer - W11753104 - Stainless Steel Dishwasher Models False F10E5 Error6 pg
Quick Reference
- Quick Start Guide2 pg
Other
- Service Pointer - W11811053 - Rev B - KitchenAid, Maytag, and Whirlpool Undercounter Dishwasher Leak At The Water Inlet Assembly_W1181105312 pg
- Service Pointer - W11715002 - RevA - Heater Nut Leaks_W117150029 pg
MyPros+ Max
Diagnose your Whirlpool MDPS6124RZ0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (50)
CodeMeaning
F1-E1Control detected K2 pilot relay stuck closed.F1-E2Control software issueF10-E1Dispenser electrical problemF10-E3Drying fan errorF10E1Dispenser Electrical Problem (also displayed as FAE1).F10E2Vent Wax Motor Electrical Problem (also displayed as FAE2).F10E3Drying Fan Electrical Problem (also displayed as FAE3).F10E4Diverter Cannot Find Positions (also displayed as FAE4).F10E5Diverter Leak Detected (also displayed as FAE5).F1E1ControlF1E2ControlF2-E1Control detected stuck key(s) in keypad or keypad connection.F2E1User InterfaceF3-E1Open connection or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failed calibration.F3E1Thermistor/OWIF3E2OWIF4-E3Wash motor not runningF4E2HeaterF4E3HeaterF5-E1Door stuck openF5-E2Door stuck closedF5E1Door SwitchF5E2Door SwitchF6-E1Low/no water (mechanical problem)F6-E2Fill valve electrical problemF6-E3Suds/air in pumpF6-E4Float switch openF6-E7Flowmeter disconnected or damaged.View all 50 error codes
F6-E8Water softener regen valve electrical problemF6E1User InterfaceF7-E1No heatF7-E2Heater stuck onF7E1Single Speed Wash Motor Failure.F7E2Variable Speed Wash Motor Failure.F7E4RIF Filter Plugged.F8-E1Slow drainF8-E2Drain motor electrical problemF8-E3Drain stuck onF8E1Inlet WaterF8E2Inlet WaterF8E3Very Low Water/Suds/Air in Pump.F8E4Overfill/Float Switch Open.F8E5Inlet WaterF8E6Flow Meter Failed.F9-E1Disconnected or damaged flowmeter.F9E1DrainingF9E2DrainingF9E4Tub Light Failure.
Service modes (8)
- Clear Error Code History["Enter Service Diagnostic Mode.","Hold the 1st button for 5 seconds to clear error code history."]
- Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
- Error Code History DisplayAfter entering Service Diagnostic Mode, press the 3rd button to display error codes
- Rapid Advance (Customer Cycle)["Start a customer cycle.","Press HIGH TEMP
- Service Diagnostic Cycle["Press START/RESUME to wake up the control panel.","Press any 3 keys in the sequence…
- Service Diagnostic ModePress any 3 keys (except Delay or Cancel) in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than 1…
- Service Test CycleAfter entering Service Diagnostic Mode, press the 2nd button (key 2) and shut the door to start the…
- User Interface TestAfter entering Service Diagnostic Mode, momentarily press the 1st button used in the entry sequence.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass