Model reference
Whirlpool WED72HEDW1
Dryer
10 documents23 error codes10 service modes
Available documentation
Service Manual
- Electronic Gas & Electric Dryers Consumer Services Technical Education Group Presents L-79 Job Aid96 pg
- Electronic Gas & Electric Dryers - Duet Sport™96 pg
- Electronic Gas & Electric Dryers96 pg
- Electronic Gas & Electric Dryers - Job Aid L-7996 pg
Tech Sheet
- Whirlpool Service Technical Sheet - Control Panel Diagnostics60 pg
Installation Guide
- Instrucciones de instalacion27 pg
- Installation Instructions24 pg
- Instrucciones de instalacion27 pg
- Installation Instructions24 pg
Quick Reference
- Quick Start Guide2 pg
MyPros+ Max
Diagnose your Whirlpool WED72HEDW1.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (23)
CodeMeaning
F-01Primary control failure in the machine control electronics.F-02Stuck button or user interface mismatch (keypad/user interface failure); only…F-22Exhaust thermistor circuit is open.F-23Exhaust thermistor circuit is shorted.F-26Motor drive system failure.F-28Moisture sensor strip circuit is open; only appears in diagnostic test mode.F-29Moisture sensor strip circuit is shorted; only appears in diagnostic test mode.F1E1Indicates a CCU (Cycle Control Unit) problem.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; this…F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor has shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; this fault code will only appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F4E1No voltage detected at the heater relay; this fault code appears ONLY when in…F4E3Restricted/low air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F6E1Communication error from UI to CCU; communication between the CCU and UI has…F6E2Communication error from CCU to UI; communication between the CCU and UI has…L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.Service modes (10)
- Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
- diagnostic1. Ensure dryer is in standby mode (plugged in with all indicators off, or only Cycle Complete…
- Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Cycle…
- Dryness Adjust Mode (Customer-Focused Drying Modes)["Activate the diagnostic test mode and advance past saved fault codes.","Press and hold the…
- dryness_adjust1
- Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
- Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
- Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
- Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
- User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dryer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass