Model reference

Whirlpool KOEC527PSS00

Name: Whirlpool KOEC527PSS00
Brand: Whirlpool

Microwave

8 documents27 error codes19 service modes

Available documentation

Service Manual

Dimension Guide12 pg
Covers this model
Tech Manual - W11382178 - Rev C64 pg
Covers this model
Tech manual60 pg
Covers this model
JennAir® and KitchenAid® 27" and 30" Microwave Combination Oven Technical Manual98 pg
Covers this model

Wiring Diagram

Wiring Sheet - W11340885 - Rev A2 pg
Covers this model

Service Flash

Service Pointer - W11802584 - Rev B - Built in Microwave Turn Table Screech3 pg
Covers this model

Quick Reference

Quick Start Guide3 pg
Covers this model

Other

Service Pointer - W11805702 - Rev A - Combo and Dedicated Microwave Cavity Door Switch_W118057029 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool KOEC527PSS00.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Microwave

F1E0 on my Whirlpool KOEC527PSS00

M+

Oven user interface (UI) failure.

From Tech Sheet W10276133, p.25:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (27)

CodeMeaning

F1E0Oven user interface (UI) failure.F1E1Internal Oven ACU (Appliance Control Unit) error.F1E4Microwave Oven Relay 4903 error.F1E5Microwave Oven Inverter error.F1E6Microwave Generation error.F2E0Keypad disconnected.F2E1Stuck/shorted key.F3E0Main oven sensor open or shorted.F3E3Meat Probe Connector Jack or Meat Probe shorted.F4E1Microwave Cavity Temperature Sensor error.F4E2Magnetron Temperature Sensor error.F4E4Microwave Oven Humidity Sensor error.F4E8Inverter over temperature.F4E9Inverter and Magnetron over temperature.F5E0Door and latch switch do not agree.F5E1Latch not operating.F6E0Oven user interface lost communication.F6E1Over temperature.F6E4User Interface / Appliance Manager state status mismatch.F6E6Oven appliance manager lost communication.F6E8Lost communications with Microwave Oven Appliance Manager.F6EAUser interface over temperature (KitchenAid models only).F8E0Product not wired correctly (cooling fan related).F8E1Low fan speed overspeed.F8E2High fan speed underspeed.F8E3High fan speed overspeed.F9E0Product not wired correctly.

Service modes (19)

Cavity Size SelectEnter Diagnostics mode (CANCEL > CANCEL > START), press numeric '3' or '6' keys to scroll to cavity…
Cavity Size Select (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
Component Activation (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Component Activation' in the Diagnostics menu and…
Diagnostic Mode1. Press LOWER OVEN > LOWER LIGHT > LOWER CANCEL (repeat two more times, total of 3 sequences). TIP
Diagnostic Mode (JennAir - touchscreen models)Press LOWER OVEN > LOWER LIGHT > OVEN CANCEL, repeat two more times (3 total sequences)
Diagnostic Mode (KitchenAid models)Press CANCEL > CANCEL > START
Diagnostics ModePress CANCEL > CANCEL > START
Error Codes (Faults Screen)Enter Diagnostics mode (CANCEL > CANCEL > START), then press numeric '3' or '6' keys to scroll to…
Error Diagnostics (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Error Diagnostics' and touch 'OK'
Faults Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
Model Selection (JennAir models)Enter Diagnostics Mode
Model Selection (within Diagnostic Mode)["Plug in oven or connect power.","Enter Diagnostics Mode.","Touch or scroll to 'System…
Model Selection Procedure1
Relay ActivationEnter Diagnostics mode (CANCEL > CANCEL > START), then press numeric '3' or '6' keys to scroll to…
Relay Activation (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
Sensors and Switches (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'Sensors and Switches' and touch 'OK'
Status ScreenEnter Diagnostics mode (CANCEL > CANCEL > START)
Status Screen (KitchenAid models)Enter Diagnostics mode (CANCEL > CANCEL > START)
System Information (JennAir models)Enter Diagnostics Mode, then touch or scroll to 'System Information' and touch 'OK'

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass