Model reference
Whirlpool GBS307PDS1
Oven
16 documents28 error codes13 service modes
Available documentation
Tech Sheet
- Tech Sheet - 975919812 pg
- Tech Sheet - 83017576 pg
- Whirlpool Oven RBS305PDQ6 Tech Sheet4 pg
- TECH SHEET - Whirlpool Range RBS305PDT1612 pg
- TECH SHEET - Whirlpool Oven YRBS305PDQ912 pg
Service Manual
- Dimension Guide1 pg
Service Flash
- Technical Service Pointer4 pg
- Service Pointer - Whirlpool and KitchenAid Built-In Single and Double Ovens2 pg
- Service Pointer - 4317445 - Rev B (Oven Does Not Operate After Self-Clean)2 pg
Installation Guide
- Installation Instructions10 pg
- Instruction Sheet1 pg
- Installation Instructions5 pg
- Installing Oven Under Cooktop4 pg
Other
- Rev A_830175812 pg
- Service Pointer 4317445 Rev B Oven Does Not Operate After Self Clean2 pg
Quick Reference
- Quick Reference Manual2 pg
MyPros+ Max
Diagnose your Whirlpool GBS307PDS1.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (28)
CodeMeaning
F0Default F codeF1 E0Communications failure or EEPROM checksum failure.F1 E2UL A/D Error(s).F1-E0Key held down too long, or key is shorted.F1-E1Keypad keytail not connected.F1-E5CANCEL key drive line open.F1-E6Electronic control malfunction (associated with CANCEL key drive line).F2 E0Shorted key detected.F2 E1Key tail error (membrane tail connection issue).F2-E0Temperature sensor opened (R=2875 ohms by spec).F2-E1Temperature sensor shorted (R=825 ohms by spec).F2-E2Oven temp too highF2-E3Oven temp too highF2-E5CANCEL key drive line open.F2-E6CANCEL key drive line open (grouped with E5).F3 E0Oven temperature sensor unplugged or open circuit.F3 E1Oven temperature sensor shorted.F3 E2Bake range over temperature condition.F3 E3Clean range over temperature condition.F3-E0Door is open but latch is locked (door switch open indicating open door and…F3-E1Self-clean latch will not lock or will not unlock.F3-E2Oven temperature too highF3-E3Oven temperature too highF5 E0Door and door switches do not agree (door position mismatch).F5 E1Door latch not operating.F5 E2Latch error during clean cycle.F5-E0Door is open but latch is locked (condition exists when door switch is open…F5-E1Self-clean latch will not lock or will not unlock.Service modes (13)
- Bake Temperature Offset AdjustmentPress BAKE key for 5 seconds
- Cavity Size Programming (Self-Clean models)Within 60 seconds of power up, press the following keys in order
- Cavity Size Programming (Standard-Clean models)Within 60 seconds of power up, press the following keys in order
- Cavity Size VerificationPress and hold CANCEL key for 5 seconds, then press and hold START key for 5 seconds. The fourth…
- Fahrenheit to Celsius ConversionPress the BROIL key for 5 seconds
- Fault Code DisplayPress and hold CANCEL key for 5 seconds
- Programming Cavity Size (Self-Clean models)1. Within 60 seconds of power up, press the following keys in sequence
- Programming Cavity Size (Standard-Clean models)1. Within 60 seconds of power up, press the following keys in sequence
- Programming the Cavity Size (Self-Clean models)Within 60 seconds of power up, press the following keys
- Programming the Cavity Size (Standard-Clean models)Within 60 seconds of power up, press the following keys
- Retrieve last error codePress and hold CANCEL/OFF key for 5 seconds
- Temperature adjustment (calibration)Press and hold BAKE pad for 5 seconds. Current offset (if any) is shown in 3-digit display. CAL is…
- Verify Cavity Size ProgrammingPress and hold CANCEL key for 5 seconds, then press and hold START key for 5 seconds.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool oven models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass