mypros+
Model reference

Whirlpool W10311752

Oven

2 documents26 error codes17 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10311752 - Rev A32 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool W10311752.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (26)

CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1 E0EEPROM communication error.F1 E1Upper RTD uncalibrated.F1 E2Lower RTD uncalibrated.F1 E5Sensor usage out of range.F1 E7PCB thermistor/sensor open or shorted.F1 E9WIDE Queue full.F2Shorted/stuck key detected on the control keypad.F2 E0Keypad disconnected.F2 E1Stuck key.F2 E2Stuck key.F3Oven sensor opened or oven sensor shorted.F3 E0Main sensor open or shorted (upper oven).F3 E1Main sensor open or shorted (lower oven).F3 E2Warming drawer temperature sensor fault.F5 E0Door and latch switches do not agree (Clean mode).F5 E1Door latch not operating (Clean mode).F5 E2Door switch fault.F6 E*Control communication failure.F6 E0Lost communications.F6 E1Over temperature during cook mode (runaway temp).F6 E2Over temperature during clean mode (runaway temp).F6 E3Over temperature in warming drawer (runaway temp).F9House miswiredF9 E0Product is mis-wired.

Service modes (17)

  • Control Reset1
  • Diagnostics ModePress CANCEL > CANCEL > START within 5 seconds.
  • Display Test1
  • Faults (Error Code Review)1
  • Faults Display1
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Semi Automatic Test1
  • Semi Automatic Test Mode1
  • Temperature CalibrationPress SETTINGS/OPTIONS until 'Temp Calib' is highlighted, then follow instructions to see the…
  • Test Mode (Manual Relay Activation)1
  • Usage Mode1
  • Version Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass