mypros+
Model reference

Whirlpool 7MWTW5560YW0

Washer

3 documents22 error codes9 service modes

Available documentation

Tech Sheet

  • Tech Sheet W10338674 Rev A44 pg
    Covers this model
  • tech sheet w10338674 reva44 pg
    Covers this model
  • Kenmore Whirlpool Washer 110 28002011 Tech Sheet44 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool 7MWTW5560YW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (22)

CodeMeaning
F0E0No fault codes stored in memory.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the main control.F2E1Stuck key detected; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of Main Control and User Interface; UI identification does not match…F3E1Pressure sensor fault; Main Control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket, or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill / long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (9)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Spin LED is On (display…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse LED is On (display…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Done LED is On (display…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Spin and Done LEDs are On…
  • Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse, Spin, and Done LEDs…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Wash and Done LEDs are On…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse and Spin LEDs are On…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax