mypros+
Model reference

Whirlpool CAE2743BQ0

Washer

3 documents23 error codes18 service modes

Available documentation

Tech Sheet

  • Whirlpool Cabrio Coin Op Washer CAE2743BQ0 Tech Sheet40 pg
    Covers this model

Service Manual

  • Job Aid - W10376706 (CL-16)_W1037670692 pg
    Covers this model
  • Whirlpool Commercial Advantage Top Load Washer Service Manual92 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool CAE2743BQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (23)

CodeMeaning
F0E0No fault detected.F0E2Over suds condition detectedF0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected during operation.F1E1Main control fault detected.F1E2Motor control faultF2E1Stuck keyF2E3Mismatch of main control and UIF3E1Pressure sensor faultF3E2Inlet water temperature faultF5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF7E1Basket speed sensor faultF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8E1No fill / long fillF8E3Overflow conditionF8E5Hot and cold inlet hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain

Service modes (18)

  • calibration["Enter diagnostic mode (see diagnostic entry sequence).","Toggle cycle selector knob until only…
  • Calibration Mode["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until only the 'Rinse' LED is…
  • Clean Washer Cycle["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until 'Sensing Load'…
  • clean_washer_cycle["Enter diagnostic mode (see diagnostic entry sequence).","Toggle cycle selector knob until status…
  • diagnostic["If washer was just plugged in or a failed attempt was made, wait 5-6 seconds before…
  • Fault Code Display Mode["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until only the 'Done' LED is…
  • fault_code_display["Enter Diagnostic Mode (left, right, right, left, right)","All LEDs should be flashing","Toggle…
  • Manual Overview Test Mode["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until 'Final Spin' and 'Done'…
  • manual_overview_test["Enter Diagnostic Mode (left, right, right, left, right)","All LEDs should be flashing","Toggle…
  • Quick Overview Test Mode["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until only the 'Final Spin' LED…
  • quick_overview_test["Enter Diagnostic Mode (left, right, right, left, right)","All LEDs should be flashing","Toggle…
  • Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off, or all indicators lit but…
  • Software Version Display Mode["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until 'Rinse', 'Final Spin', and…
  • sw_version_display["Enter diagnostic mode (see diagnostic entry sequence).","Toggle cycle selector knob until Rinse…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until 'Soak/Wash' and 'Done'…
  • tachometer_verification["Enter diagnostic mode (see diagnostic entry sequence).","Toggle cycle selector knob until…
  • UI Test Mode["Enter Service Diagnostic Test Mode.","Toggle cycle selector knob until 'Rinse' and 'Final Spin'…
  • ui_test["Enter diagnostic mode (see diagnostic entry sequence).","Toggle cycle selector knob until Rinse…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax