mypros+
Model reference

Whirlpool RTW4519PW0

Washer

3 documents21 error codes8 service modes

Available documentation

Tech Sheet

  • Technical Service Sheet W1144864320 pg
    Covers this model

Service Flash

  • Service Pointer - W11787221 - Rev B - Top-Load Washer Control Board Housing Needs to be Replaced15 pg
    Covers this model
  • Service Pointer - W11766193 - Rev F - Top Load Washer and Stacked Laundry - F3E1 Pressure Sensor Error or Drain Pump Running Continuously9 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool RTW4519PW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (21)

CodeMeaning
F0E2Over suds condition detected; suds prevent the basket from spinning up to speed…F0E4High water temperature detected during rinse cycle (105°F or higher).F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Switch mismatch; the switches do not match the console or are not operating…F3E1Pressure system fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open, or control not…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed fault; main control cannot determine speed of basket, or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill or long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (8)

  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until Spin LED is On (all…
  • Calibration Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse LED is On (all…
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until Done LED is On (all…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until Spin and Done LEDs are…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 10 seconds after…
  • Software Version Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse, Spin, and Done…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until Wash and Done LEDs are…
  • UI Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse and Spin LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass