mypros+
Model reference

Whirlpool W11169652B

Washer

1 document28 error codes8 service modes

Available documentation

Service Manual

  • Service Manual Whirlpool & Maytag 27" Front-load Washers94 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool W11169652B.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (28)

CodeMeaning
F0E1Load detected inside the drum during the Clean Washer cycle.F0E2Oversuds condition detected by the pressure sensor; ACU will flush water to…F0E5Off balance load condition detected during the cycle.F1E1Appliance Control Unit (ACU) fault.F1E2Fault of the motor control section of the ACU.F3E1Water level sensor fault; ACU detects an out of range pressure signal.F3E2Wash NTC (temperature sensor) fault; sensor is out of range, open circuit, or…F3E5Dry NTC (temperature sensor) fault; sensor is out of range, open circuit, or…F3E6Accelerometer fault; accelerometer failed self test or experienced orientation…F4E1Wash heater relay error or no feedback signal; ACU cannot detect temperature…F4E2Heater not turning on; wash heater relay is not closed.F4E4Vent Fan Motor fault or Dry Blower Motor fault; open circuit or short circuit…F5E1Door switch fault; door switch is open while the door is locked for more than 5…F5E2Door lock will not lock or door lock failure; door will not close completely…F5E3Door unlock failure; washer is unable to unlock the door or ACU cannot…F5E4Door not opened between cycles; user presses START with door open or after a…F6E1Communication errorF6E2Communication errorF6E3No communication between ACU and MCU (Motor Controller).F7E2Motor control internal fault; ACU has detected a problem with the motor.F7E8Motor control over temperature detected.F7E9Motor locked rotor condition.F7EAMotor control lost phase fault.F7ECMotor control/motor overload fault.F8E1Long fill; water level does not change for a period of time or ACU does not…F8E3Overflow condition detected.F9E1Long drain; water level sensor does not change after the drain pump is on.FCE0WiFi error; HMI cannot communicate with the WiFi module.

Service modes (8)

  • Component Activation Test (LCD in Door Models)["Activate Service Diagnostic Mode (LCD) first.","From the DIAGNOSTICS HOME screen, scroll down and…
  • Fault/Error Code Display (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 3rd button used to activate…
  • Human-Machine Interface (HMI) Test (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Load Test and Quick Service Cycle (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Quick Service Cycle (LCD in Door Models)["Activate Service Diagnostic Mode (LCD) first.","From the Component Activation screen, select…
  • Service Diagnostic Mode (Console Models)["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 30 seconds after…
  • Service Diagnostic Mode (LCD in Door Models)["Ensure washer is in standby mode (plugged in with all indicators off).","Open and close the…
  • Software Version Display (Console Models)["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass