mypros+
Model reference

Whirlpool W11647908

Washer

1 document24 error codes13 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11647908 - Rev B24 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool W11647908.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (24)

CodeMeaning
F0 E5Off balance load detected during cycle operation.F1 E1Indicates a fault has occurred in the main control.F1 E6Control board recognized line voltage below 90 V AC.F2 E1Washer keypad is sensed pressed for continued duration (stuck key error).F3 E2Main control detects an out of range pressure signal from the pressure sensor.F3 E3Inlet water temperature faultF5 E1Lid switch faultF5 E3Lid switch faultF5 E4Lid unlock faultF7 E1Basket speed sensor faultF7 E2Motor control faultF7 E5Shifter faultF8 E1No fillF8 E3Overflow conditionF9 E1Long drainFC E1No model/serial number information is saved on the machine's controls.FC E2Model/serial number information saved on the machine's controls is not the same…FC E4USB stick failureFC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFP E1Coin 1 circuit error.FP E2Coin 2 circuit error.FP E3Card reader communication error.

Service modes (13)

  • Calibration Cycle (P-05)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-05' is displayed.","Press START…
  • Clean Washer Cycle (P-12)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-12' is displayed.","Press START…
  • Clear Errors (P-01)["Enter Service Diagnostic Test Mode.","Display shows 'P-01'.","Press START to clear active error…
  • Cycle Credit (P-02)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-02' is displayed.","Press START…
  • Drain & Spin Cycle (P-06)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-06' is displayed.","Press START…
  • Help Mode["Enter Service Mode.","Use MIXED keypad to advance to program location 2.xx (Special Pricing…
  • Manual Overview Test (P-04)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-04' is displayed.","Press START…
  • Quick Overview Test (P-03)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-03' is displayed.","Press START…
  • Service Diagnostic Test Mode (Coin Models)["Remove the service cover on the metercase.","Press and hold the DELICATES keypad for 1 second
  • Service Diagnostic Test Mode (Free Vend)["If washer is set for Free Vend, press the following keypads within 6 seconds
  • Tachometer Verification (P-09)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-09' is displayed.","Press START…
  • Technician Service Access Code (Non-Coin Free Vend models only)["Press the HEAVY DUTY, EXTRA RINSE, TEMPERATURE, and DELICATES keypads within 10 seconds."]
  • UI Diagnostics (P-07)["Enter Service Diagnostic Test Mode.","Press MIXED keypad until 'P-07' is displayed.","Press START…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass