mypros+
Model reference

Whirlpool WTW4800XQ0

Washer

18 documents22 error codes17 service modes

Available documentation

Tech Sheet

  • Diagnostic LED, Diagnostic Test Mode and Error Code summary sheet3 pg
    Covers this model
  • techsheet w10280489 revd48 pg
    Covers this model
  • Tech Sheet W10280489 Rev D21 pg
    Covers this model

Service Flash

  • Installation Pointer - W10547923 (Software Enhancement)3 pg
    Covers this model
  • TECHNICAL SERVICE POINTER - Testing Agitation during a TEST MODE2 pg
    Covers this model
  • Technical Installation Pointer - Software Enhancement VMW Classic Top-Load, Belt-Drive Washers3 pg
    Covers this model
  • Technical Service Pointer2 pg
    Covers this model
  • Service Pointer - W10411107 (Broken Lid Lock)1 pg
    Covers this model
  • Service Pointer - W10405379 - Rev A (Elimination of Counter Weight)1 pg
    Covers this model
  • Technical Service Pointer #W10492393 - Drive (Splutch) Pulley Comes Loose6 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
  • Instruction Sheet4 pg
    Covers this model

Training

  • Training Pointer - W10504063 (Software Enhancement)3 pg
    Covers this model
  • Training Pointer - 8178817 (Washer not Filling at Cycle)3 pg
    Covers this model

Installation Guide

  • Instrucciones de instalación10 pg
    Covers this model

Other

  • Whirlpool Washer Agitator Dog 285809 Instruction Sheet 2857471 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW4800XQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the main control board.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and User Interface; UI identification does not match…F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill or long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (17)

  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • automatic_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Spin' LED is…
  • calibration["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Rinse' LED is…
  • Calibration Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • diagnostic (service diagnostic test modes entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • fault_code_display["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Done' LED is…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • manual_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' and 'Done' LEDs are…
  • Service Diagnostic Test ModeRefer to the Service Tech Sheet located inside the unit front top corner for the specific button…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • sw_version_display["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse', 'Spin', and 'Done'…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • tachometer_verification["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash' and 'Done' LEDs are…
  • UI Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • ui_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' and 'Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass