mypros+
Model reference

Whirlpool WTW4850XQ3

Washer

13 documents43 error codes12 service modes

Available documentation

Tech Sheet

  • Diagnostic LED, Diagnostic Test Mode and Error Code summary sheet3 pg
    Covers this model
  • w10468340 tech sheetpdf wtw4900aw048 pg
    Covers this model
  • TechSheet W10468340 RevC48 pg
    Covers this model
  • Kenmore Whirlpool Modular Washer 110 21302013 Tech Sheet48 pg
    Covers this model

Service Manual

  • Vertical Modular Washer84 pg
    Covers this model
  • Vertical Modular Washer84 pg
    Covers this model

Service Flash

  • Service Pointer - W10411107 (Broken Lid Lock)1 pg
    Covers this model
  • Service Pointer - W10405379 - Rev A (Elimination of Counter Weight)1 pg
    Covers this model
  • Technical Service Pointer - Continuous Test Mode3 pg
    Covers this model
  • Technical Service Pointer #W10492393 - Drive (Splutch) Pulley Comes Loose6 pg
    Covers this model

Tech Tip

  • Service Pointer - W10657326 (Customer Tip Sheet)3 pg
    Covers this model

Installation Guide

  • Instrucciones de instalación10 pg
    Covers this model

Other

  • Whirlpool Washer Agitator Dog 285809 Instruction Sheet 2857471 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW4850XQ3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
F0 E2Over suds condition detectedF0 E4High water temperature during rinse cycleF0 E5Off balance load detected.F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected during cycle.F1 E1Main control fault.F1 E2Motor control faultF1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2 E1Stuck keyF2 E3Mismatch of main control and UIF2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and User Interface identification; UI ID does not…F3 E1Pressure sensor faultF3 E2Inlet water temperature faultF3E1Pressure system fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor is detected to be open or…F5 E1Lid switch faultF5 E2Lid lock faultF5 E3Lid unlock faultF5 E4Lid not opened between cyclesF5E1Lid switch fault; lid is in locked state but lid switch is open, control not…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7 E1Basket speed sensor faultF7 E5Shifter faultF7 E6Motor fault
View all 43 error codes
F7 E7Motor unable to reach target RPMF7E1Basket speed fault; main control cannot determine speed of basket, or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8 E1No fill / long fillF8 E3Overflow conditionF8 E5Hot and cold water supply hoses are reversed.F8E1No fill or long fill; water level does not change for a period of time OR water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9 E1Long drainF9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (12)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' LED is On.","Press…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' LED is On.","Press…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Done' LED is On.","Press…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin & Done' LEDs are…
  • Sales Demo Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse & Done' LEDs are On and…
  • Service Diagnostic Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test ModeRefer to the Service Tech Sheet located inside the unit front top corner for the specific button…
  • Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse, Spin, and Done'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse & Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass